Results 81 to 90 of about 69,485 (297)
Regional boundary of initial bending stiffness of semi-rigid joint under the positive bending.
, 2022 Regional boundary of initial bending stiffness of semi-rigid joint under the positive bending.
Liang Wang (23021) +7 more
core +1 more source
Advanced Engineering Materials, EarlyView.This article presents an experimental and numerical modal investigation of composite sandwich structures using surfboards as model systems. By comparing different core materials and reinforcement strategies, the study demonstrates how local stiffeners influence vibrational response and introduce characteristic modal features, highlighting modal ...
Brett Connellan +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Yantu gongcheng xuebao, 2019 Aiming at different types of bolted joints, taking into account the discontinuity of complex joints and the pre-tightening force of joints, the longitudinal joints of shield tunnel segments of Z2 metro line in Tianjin Binhai New Area are studied.
ZHANG Wen-jun 1, 2, ZHANG Qi 1, 2, ZHANG Gao-le 1, 2
doaj +1 more source
Nonlinear vibration isolators with asymmetric stiffness
, 2012 A vibration source is commonly coupled to a receiving structure by a vibration isolator. A key trade-off in the choice of vibration isolator is the requirement for a wide frequency range of isolation without excessive static deflection.
Abolfathi, A.
core
Structural response of concrete-filled elliptical steel hollow sections under eccentric compression [PDF]
, 2012 The purpose of this research is to examine the behaviour of elliptical concrete-filled steel tubular stub columns under a combination of axial force and bending moment. Most of the research carried out to date involving concrete-filled steel sections has
Sheehan, Therese +9 more
core +1 more source
Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method
Advanced Engineering Materials, EarlyView.A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley +1 more source
Study of the Carrier-Aided Thin Film Electrode Array Design for Cochlear Insertion
Micromachines, 2018 The micro-fabricated thin film electrode array (TFEA) has been a promising design for cochlear implants (CIs) because of its cost-effectiveness and fabrication precision.
Yuchen Xu +5 more
doaj +1 more source
Hybrid Metal–Carbon Ink for Printed Stretchable Temperature Sensors
Advanced Engineering Materials, EarlyView.We prepare conductive inks for temperature sensing with silver flakes and carbon or graphite flakes in a silicone elastomer matrix. Silver dominates the temperature‐dependent conductivity, while the carbon filler network ensures the stability of the conductive pathways and retains function under strain.
Makara Lay +3 more
wiley +1 more source
Calculation on Bending Stiffness of RC Short Beam Strengthened by CFRP
Advances in Civil Engineering, 2020 Based on the bending tests of seven reinforced concrete (RC) short beams strengthened with carbon fiber reinforced polymer (CFRP), the bending stiffness curves of the whole process of the short beams strengthened with CFRP were obtained.
Wang Tingyan, Zhou Yun, Zhang Junwei
doaj +1 more source