Results 111 to 120 of about 5,555 (195)
International Journal for Numerical and Analytical Methods in Geomechanics, Volume 50, Issue 5, Page 2470-2485, 10 April 2026.ABSTRACT Localized deformation in dense granular materials, often culminating in the formation of shear bands, is a key failure mechanism in geotechnical and material systems. However, predicting the onset of such localization remains a fundamental challenge due to the system's inherent inelasticity and microstructural complexity.
Zhennan Zhu +4 more
wiley +1 more source
Biomechanical Variation of the Vessel Wall Along the Length of the Healthy Aorta-Linking Geometric, Flow-, and Pressure-Mediated Adaptations. [PDF]
J Biomech EngBadal RM, Barocas VH.
europepmc +1 more source
Packaging Technology and Science, Volume 39, Issue 4, Page 419-440, April 2026.The 3D formability of paperboard was examined using full and localised microfibrillated cellulose (MFC) coatings in thermoforming, hydroforming and deep drawing, and the results were linked to bulge‐test strain behaviour. Full‐surface fluidised MFC coatings consistently improved strain capacity and 3D formability, achieving performance comparable to ...
Sanaz Afshariantorghabeh +3 more
wiley +1 more source
Anisotropic pullout behavior of bauxite slag-geogrid interfaces. [PDF]
Sci RepZhao Z, Chen J, Sun Z, Zhang J.
europepmc +1 more source
The plasticisation model of dye diffusion: Part 5
Coloration Technology, Volume 142, Issue 2, Page 296-326, April 2026.Abstract The findings presented in the previous part of the paper (Part 4) of the re‐evaluation of previously published data reported for the temperature‐dependent diffusion of an organic acid within nylon 6 film, desorption of three acid dyes from dyed nylon 66 fabric, diffusion of an acid dye within nylon 6 monofilaments and adsorption of a sulphur ...
Stephen M. Burkinshaw
wiley +1 more source
Evaluation of Creep Life and Damage for AISI 304 Under Combined Tension/Torsion Multiaxial Loading
Fatigue &Fracture of Engineering Materials &Structures, Volume 49, Issue 4, Page 1327-1339, April 2026.ABSTRACT In the present study, to investigate the effects of temperature and principal stress ratio on the multiaxial creep rupture time of AISI 304 stainless steel, creep tests were conducted under various principal stress ratios at 650°C and 700°C.
Lei He, Takamoto Itoh, Noritake Hiyoshi
wiley +1 more source
An Image-Based Computational Framework to Evaluate the Material Stiffness of Arterial Tissue With High-Resolution Magnetic Resonance Imaging. [PDF]
J Biomech EngWang YFJ +7 more
europepmc +1 more source
International Journal of Applied Glass Science, Volume 17, Issue 2, April 2026.ABSTRACT The formation of a crystallized surface layer, having a lower coefficient of thermal expansion (CTE) than the parent glass, can be exploited to place the glass surface under compression during cooling from crystallization temperature and hence improve mechanical properties.
Fabian Stoelzel, Thorsten Gerdes
wiley +1 more source
A PHYSICS-GUIDED SMOOTHING METHOD FOR MATERIAL MODELING WITH DIGITAL IMAGE CORRELATION (DIC) MEASUREMENTS. [PDF]
Proc Int Conf Image ProcWang J, Lee CH, Richardson W, Yu Y.
europepmc +1 more source
Strain, Volume 62, Issue 2, April 2026.This study applies nanoindentation to resolve layer‐specific mechanical properties in photovoltaic backsheet multilayer polymers. Structural compliance correction reduces substrate flexure and edge artefacts, enabling reliable hardness and modulus mapping.
P. Christoefl +6 more
wiley +1 more source