Results 141 to 150 of about 36,042 (286)
Journal of the Mechanical Behavior of MaterialsMultiaxial creep investigations at high temperatures are required to guarantee the integrity of structural materials such as boiler pipes for power generation and turbine blades for aviation and industrial applications.
Hiyoshi Noritake
doaj +1 more source
Shear work induced changes in the rheology of model Mozzarella cheeses : a thesis presented in partial fulfilment of the requirements for the degree of Doctor of Philosophy in Food Technology at Massey University, Manawatu, New Zealand [PDF]
, 2016 Mozzarella cheese is a pasta filata type of cheese. Its manufacture includes a kneading – stretching step that creates a fibrous protein network and distributes fat-serum channels to attain desirable melt functionality on a pizza.
Sharma, Prateek
core
Fire and Materials, EarlyView.ABSTRACT This study addresses the influence of fibre architecture on the mechanical properties of vacuum‐infused glass fibre reinforced polymer (GFRP) composites at elevated temperatures (ET). Laminates with three different fibre configurations—unidirectional (UD), bidirectional 0°/90° cross‐ply (BD), and ±45° off‐axis angle‐ply (OA) – were tested in ...
Eloísa Castilho +4 more
wiley +1 more source
HOST structural analysis program overview [PDF]
Hot-section components of aircraft gas turbine engines are subjected to severe thermal structural loading conditions, especially during the startup and takeoff portions of the engine cycle.
Thompson, Robert L.
core +1 more source
Comparison of gurson and lemaitre model in the context of blanking simulation of a high strength steel [PDF]
, 2017 The process of blanking takes place in a short band with high accumulated strain undergoing various stress triaxialities. Enhanced implementations for shear and compressive loads of Gurson’s and Lemaitre’s model are directly compared for the same ...
Clausmeyer, Till +3 more
core
Neurourology and Urodynamics, EarlyView.ABSTRACT Introduction Pelvic organ prolapse is a common condition and many women seek surgical treatment for prolapse symptoms. However, recurrence of prolapse after surgical treatment is common. A think tank was held at ICI‐RS 2025 to discuss how the assessment and indifferent results from conservative and surgical management can be improved.
Rohna Kearney +9 more
wiley +1 more source
Polymer Composites, EarlyView.Schematic illustration of ±45° tensile testing, including detection of first‐ply failure (FPF) by optical crack detection and acoustic emission monitoring, comparison of FPF values with ASTM D3518 and D3039 criteria, and resulting ply level stress states at FPF for GF‐ and CF‐epoxy laminates.
Maria Gfrerrer +4 more
wiley +1 more source
A probabilistic high cycle fatigue model applied to cast Al-Si alloys [PDF]
, 2013 In this work, the high cycle fatigue behavior of cast hypo-eutectic Al-Si alloys is investigated. It is observed that two different coexisting fatigue initiation mechanisms can occur in these materials depending on the presence of different ...
AUGUSTINS, Louis +3 more
core +3 more sources
Polymer Composites, EarlyView.Graphical representation of the wear‐mode‐dependent tribological behavior of graphene nanoplatelet (GNP) modified glass fiber‐reinforced epoxy composites, highlighting the distinct mechanisms governing dry sliding wear and solid particle erosion. ABSTRACT Glass fiber‐reinforced epoxy composites are widely used in structural applications where surface ...
Elif Gültürk +2 more
wiley +1 more source
A material model for warm forming of aluminium sheet [PDF]
, 2003 A material model has been developed to simulate the warm forming of Al–Mg\ud sheet. Both the hardening behaviour, including temperature and strain rate effects, and the\ud biaxial stress–strain response of the sheet are considered.
Bolt, P.J., Boogaard, A.H. van den
core +2 more sources