Results 71 to 80 of about 253,198 (311)
New Natural Injection-Moldable Composite Material from Sunflower Oil Cake [PDF]
, 2006 Through a twin-screw extrusion process the native structure of sunflower oil cake was completely transformed (globular protein denaturation/texturization and husk fiber defibration) into a simpler matrix-fiber structure, as could be seen on SEM ...
A. Rouilly +30 more
core +2 more sources
Advanced Functional Materials, EarlyView.Bio‐based and (semi‐)synthetic zwitterion‐modified novel materials and fully synthetic next‐generation alternatives show the importance of material design for different biomedical applications. The zwitterionic character affects the physiochemical behavior of the material and deepens the understanding of chemical interaction mechanisms within the ...
Theresa M. Lutz +3 more
wiley +1 more source
Advanced Functional Materials, EarlyView.A food‐grade cooling composite made from starch and recycled eggshell powder offers a scalable, ultra‐low‐cost solution for passive daytime radiative cooling. Easily prepared using basic kitchen tools, this material empowers communities, even in areas with limited infrastructure, to stay cooler during worsening summer heat waves.
Qimeng Song +3 more
wiley +1 more source
Characterisation of untreated and treated biodegradable wastes [PDF]
, 2007 As part of a Defra sponsored project (WRT220), approximately 40 biodegradable wastes were characterised according to biodegradability (DR4 and BM100), total PTE content, C:N ratio and biochemical composition.
Blakey, N. +4 more
core
Effect of starch physiology, gelatinization, and retrogradation on the attributes of rice starch-ι-carrageenan film [PDF]
, 2017 Edible films and coatings have been applied as the potential substitutes for conventional plastics in food packaging. However, their physical and mechanical properties still have limitations and thus require further improvement.
Bowyer, Michael +7 more
core +2 more sources
Advanced Functional Materials, EarlyView.Fibrous benzenetrispeptide (BTP) hydrogels, fabricated via strain‐promoted azide‐alkyne cycloaddition (SPAAC) crosslinking, form robust, bioinert networks. These hydrogels can support 3D cell culture, where cell viability and colony growth depend on the fiber content.
Ceren C. Pihlamagi +5 more
wiley +1 more source
Ecological Protection: Cell Phone Stand with Cable Winding Made of Polypropylene
Engineering ProceedingsIn an increasingly digitized environment, the deterioration of cell phone cables has led to a significant environmental impact due to the lack of adequate protection and care.
Deysi Vanessa Canchis Paredes +2 more
doaj +1 more source
The Compositions: Biodegradable Material – Synthetic Resins as Moulding Sands Binders
Archives of Foundry Engineering, 2016 Growing emission requirements are forcing the foundry industry to seek new, more environmentally friendly solutions. One of the solutions may be the technologies of preparing moulding and core sands using organic biodegradable materials as binders ...
Major-Gabryś K. +2 more
doaj +1 more source
Lignocellulosic Recycled Materials to Design Molded Products: Optimization of Physical and Mechanical Properties [PDF]
, 2016 The object is to contribute to the reduction of environmental pollution, by reusing a fraction of urban solid waste, forestry and agroindustrial waste: newspaper (ONP), office paper (OWP), corrugated cardboard (OCC), pine sawdust, eucalyptus sawdust and ...
Aguerre, Yanina Susel +1 more
core +2 more sources
Material model proposal for biodegradable materials
Procedia Engineering, 2011 AbstractA large range of biodegradable polymers are used in many products with short life cycle. Important applications of these are found in the biomedical field, where biodegradable materials are used to produce scaffolds that temporarily replace the biomechanical functions of a biologic tissue, while it progressively regenerates its capacities ...
Vieira, A.C. +3 more
openaire +1 more source