Results 211 to 220 of about 4,542 (246)

Experimental Investigation of the Blade Tip Timing (BTT) Uncertainties [PDF]

, 2022
The uncertainties of blade tip displacement measurement using BTT are investigated through experiments. A novel test bench is established where the blade deformation can be measured simultaneously by laser displacement sensors and BTT, which enables the determination of the BTT measurement error.
Xiao, Zhicheng, Meng, Yiming, Ouyang, Hua   +2 more
openaire   +1 more source

Some of the next articles are maybe not open access.

Related searches:

Blade Tip Timing: from Raw Data to Parameters Identification

2019 IEEE International Instrumentation and Measurement Technology Conference (I2MTC), 2019
Blade Tip Timing (BTT) methods have been increasingly implemented for blade health monitoring. However, most of them are based on the prior knowledge that the resonance’s location is known. Since real BTT test usually takes more than ten hours, it’s unrealistic to Figure out every resonance from the measured raw data manually.
Shuming Wu, Xuefeng Chen 0002, Pete Russhard, Ruqiang Yan 0001, Shaohua Tian, Shibin Wang, Zhibin Zhao 0002   +6 more
openaire   +1 more source

On the development of a magnetoresistive sensor for blade tip timing and blade tip clearance measurement systems

AIP Conference Proceedings, 2014
A simultaneous blade tip timing (BTT) and blade tip clearance (BTC) measurement system enables the determination of turbomachinery blade vibrations and ensures the monitoring of the existing running gaps between the blade tip and the casing. This contactless instrumentation presents several advantages compared to the well-known telemetry system with ...
R. Tomassini, G. Rossi, J.-F. Brouckaert
openaire   +2 more sources

Blade-Tip Timing Measurement Of Synchronous Vibrations Of Rotating Bladed

2002
Blade-tip timing (BTT) is a promising method for the detection, measurement and analysis of blade vibrations in rotating bladed assemblies. However, the intricacies of the method when applied to real rotating structures undergoing synchronous (Engine Ordered) vibrations are not yet fully understood.
Dimitriadis, Grigorios, Carrington, Ian B., Wright, Jan Robert, Cooper, Jonathan E   +3 more
openaire   +1 more source

Calibration of blade tip-timing sensor for shrouded 40″ last stage blade

Mechanical Systems and Signal Processing, 2018
Abstract Today’s power generation market requests steam turbines of high efficiency, reliability and wide operation range. The last stage moving blades are designed with integral shroud, mid-span, and fir-tree dovetail. The blades are continuously coupled by the blade untwist due to the centrifugal force, and thus the vibration control and increased ...
Kubín, Z., Mísek, T., Hlous, J., Dadaková, T., Kellner, J., Bachorec, T.   +5 more
openaire   +1 more source

A blade damage identification method based on bladed disk modal analysis and blade tip timing

Aerospace Science and Technology
Blade damage diagnosis is a critical requirement for ensuring operational safety and reliability in aero-engines and gas turbines. Blade tip timing (BTT) is a well-established non-contact vibration monitoring technique. However, most existing damage detection methods focus on single-blade response analysis, which suffers from diagnostic latency and can
Pengfei Chai, Shang Wang, Yiming Meng, Zhicheng Xiao, Jie Tian, Yong Chen, Hua Ouyang   +6 more
openaire   +1 more source

Rotating blade frequency identification by single-probe blade tip timing

Mechanical Systems and Signal Processing, 2022
Jia-Hui Cao, Zhi-Bo Yang, Hao-Qi Li, Guang-Rong Teng, Shao-Hua Tian, Wen-Bo Li, Xue-Feng Chen   +6 more
openaire   +1 more source

Compressed Covariance Sensing for Blade Tip Timing

2023
Jiahui Cao, Zhibo Yang, Xingwu Zhang, Xuefeng Chen   +3 more
openaire   +1 more source

Mistuning identification and model updating approach for bladed disks based on blade tip timing

Journal of Sound and Vibration, 2023
Daitong Wei, Hongkun Li, Peixin Gao, Yugang Chen, Chuang Wang   +4 more
openaire   +1 more source

Measurement Methodology: Blade Tip Timing: A Non-Contact Blade Vibration Measurement Method

IEEE Instrumentation & Measurement Magazine, 2023
Haoqi Li, Shuming Wu, Zhibo Yang 0001, Ruqiang Yan 0001, Xuefeng Chen 0002   +4 more
openaire   +1 more source