Results 101 to 110 of about 1,330,518 (288)
A 4‐layer Kevlar‐based composite is fabricated by combining ultrasonic spraying and electrostatic flocking. Carbon black dispersion is first deposited onto Kevlar fabric to create a conductive electrode. Nylon fibers are then electrostatically flocked onto the coated fabric, forming a dielectric layer.
Mengdi Chen +7 more
wiley +1 more source
Advanced Manufacturing of Composite‐Based Systems for Energy Applications
Advanced manufacturing enables the integration of polymers, ceramics, metal oxides, and composites into architected microstructures with tailored transport pathways. By coupling material selection, manufacturing strategy, and structural design, multifunctional energy systems can simultaneously improve electrochemical performance, thermal management ...
Sri Vaishnavi Thummalapalli +13 more
wiley +1 more source
Desktop vacuum thermoforming enables rapid, low‐cost fabrication of 96‐channel polystyrene culture chips with very thin imaging interfaces. The resulting platform supports cell lines, primary cells, and patient‐derived organoids, and enables high‐resolution confocal microscopy and single‐cell visualization, providing an accessible approach for advanced
Aleksandra Fomina +5 more
wiley +1 more source
Analysis of the Fracture of Reinforced Concrete Flat Elements Subjected to Explosions. Experimental Procedure and Numerical Validation [PDF]
Many of the material models most frequently used for the numerical simulation of the behavior of concrete when subjected to high strain rates have been originally developed for the simulation of ballistic impact.
Cendón Franco, David Ángel +4 more
core +1 more source
Collision‐Resilient Winged Drones Enabled by Tensegrity Structures
Based on structures of birds such as the woodpeck, this article presents the collision‐resilient aerial robot, SWIFT. SWIFT leverages tensegrity structures in the fuselage and wings which allow it to undergo large deformations in a crash, without sustaining damage. Experiments show that SWIFT can reduce impact forces by 70% over conventional structures.
Omar Aloui +5 more
wiley +1 more source
This review identifies key design considerations for insect‐inspired microrobots capable of multimodal locomotion. To draw inspiration, biological and robotic strategies for moving in air, on water surfaces, and underwater are examined, along with approaches for crossing the air–water interface.
Mija Jovchevska +2 more
wiley +1 more source
FiN‐Kiri: Fabric‐Based Inflatable Kirigami Actuator for Multimodal Soft Robots
This study introduces a type of inflatable fabric‐based kirigami actuator capable of performing bending motion. The actuator is utilized as soft grippers, a crawling robot and a swimming robot. The crawling robot demonstrated extraordinary motion capabilities, such as moving forward, turning and navigating a narrow tunnel.
Yang Yu +12 more
wiley +1 more source
How much load can my pallet carry?
Properly determining the exact load carrying capacity of a pallet is essential to ensure the effectiveness of the supply chain. Multiple testing procedures are published by different organizations and all could be used to estimate the load capacity of ...
Horvath, Laszlo
core
Innate Immunocompetent hiPSC‐Derived Neurospheroids Capture Early CNS Responses to rAAV
Knowledge of human CNS immune responses to AAV‐based gene therapies remains limited due to the lack of immune‐competent human models. Here, a hiPSC‐derived 3D neuroimmune platform integrating neurospheroids and microglia is established using stirred‐tank bioreactors.
Catarina M. Gomes +14 more
wiley +1 more source
The pre‐regenerative vascular niche (PVN) is essential for nerve repair, yet its endothelial blueprint remains unclear. We identified angiogenic ECs (AECs) as the dominant pre‐regenerative subset and found that antler blood–derived exosomes (AB‐EXO) promote repair via IMP3.
Jinsheng Huang +11 more
wiley +1 more source

