Results 61 to 70 of about 1,257 (242)

Smart Bioinspired Material‐Based Actuators: Current Challenges and Prospects

Advanced Intelligent Systems, Volume 7, Issue 3, March 2025.
This work gathers, in a review style, an extensive and comprehensive literature overview on the development of autonomous actuators based on synthetic materials, bringing together valuable knowledge from several studies. Furthermore, the article identifies the fundamental principles of actuation mechanisms and defines key parameters to address the size
Alejandro Palacios, Léon Chiriatti, Simon Poppinga, Thomas Speck, Vincent Le Houérou   +4 more
wiley   +1 more source

Pre‐Curved Everting Robots With Embedded Steering Intelligence Fabricated by CO2 Laser Welding

Advanced Intelligent Systems, EarlyView.
Design and experimental demonstration of a laser welded growing robot for anatomically guided navigation. The robot follows an aortic arch phantom entering the branchiocephalic branch through steering by design. The figure shows the physical phantom setup, CAD defined weld geometry and full robot eversion.
Brandon Saldarriaga, Panagiotis Kalozoumis, Panagiotis Vartholomeos, Carlo Seneci, Kawal Rhode, Christos Bergeles   +5 more
wiley   +1 more source

Structure, mechanical, and electrical properties of high-density polyethylene/multi-walled carbon nanotube composites processed by compression molding and blown film extrusion

, 2015
The structure and properties of melt mixed high-density polyethylene/multi-walled carbon nanotube (HDPE/MWCNT) composites processed by compression molding and blown film extrusion were investigated to assess the influence of processing route on ...
Harkin-Jones, Eileen, Martin, Peter, Xiang, Dong, Linton, David   +3 more
core   +1 more source

Evaluation of the Efficiency of a Biobased Reactive Plasticizer on the Morphology and Properties of Sustainable Flexible Films Based on Poly(Lactic Acid) (PLA) Produced by Blown Film Extrusion

Journal of Applied Polymer Science, EarlyView.
A comparative investigation of two epoxy additives derived from cardanol (NC513 and NC514s) for production of films based on poly (lactic acid) (PLA), acetyl tributyl citrate (ATBC), and poly (butylene adipate‐co‐terephthalate) (PBAT) clarified their distinct roles, with NC513 mainly acting as a plasticizer, reducing viscosity and enhancing ductility ...
Norma Mallegni, Vito Gigante, Patrizia Cinelli, Andrea Lazzeri   +3 more
wiley   +1 more source

Development of a blown tubular film extrusion die and air ring

, 1973
This creative project has investigated the engineering principles relative to the design and fabrication of both a blown tubular film extrusion die and an air ring.
Snader, Kenneth R., 1950-
core  

Fiber‐type soft bioelectronics for wearable and implantable sensing and therapy

BMEMat, EarlyView.
Fiber‐type soft bioelectronics are emerging as versatile platforms for wearable and implantable health monitoring and therapeutic applications. These bioelectronics use organic and inorganic matrices combined with advanced fillers, which feature high conductivity, electrochemical sensitivity, softness, and biocompatibility.
Haneul Kim, Hak Yong Kim, Ja Hoon Koo, Gi Doo Cha, Dae‐Hyeong Kim, Hye Jin Kim   +5 more
wiley   +1 more source

Influence of carbon nanotubes on the properties of films of polypropylene prepared by film blowing

, 2008
The influence of carbon nanotubes on mechanical and bielongational properties of films of polypropylene prepared with film blowing technique were studied.
Iannace, Francesca
core  

Lithium Metal Anode Fabrication: Methods, Challenges, and Strategies

EcoEnergy, EarlyView.
Schematic illustration of four representative fabrication techniques for thin lithium metal anodes: extrusion, molten lithium infusion, electroplating, and physical vapor deposition (PVD). ABSTRACT The pursuit of ultra‐high energy‐dense lithium‐metal batteries (LMBs) has reignited the drive to fabricate ultrathin high‐quality lithium metal anodes. This
Ji Hyun Baek, Mi Ji Kang, Ho Won Jang
wiley   +1 more source

Effect of a Biodegradable Additive on the Mechanical Properties of LDPE Blown Films: A Statistical and Machine Learning Approach

Revista de Ciencias Tecnológicas
This study evaluates the effect of incorporating the biodegradable additive P–Life on the mechanical properties of ice bags (IB) made from low-density polyethylene (LDPE).
Gilberto Alarcón Aguilar, Alam Josué Reyes López, Frixia Galán Méndez   +2 more
doaj   +1 more source

Expert system for blown film extrusion

, 1991
Expert systems and blown film extrusion are two subjects to deal with in this thesis. Expert systems are an aspect of artificial intelligence, or a computer\u27s ability to think. The determination of a suitable expert system for particular problem is an
Li, Jiachyi
core