Results 221 to 230 of about 246,187 (316)

Comparative analysis of heat impacts on bond strength and failure modes of calcium silicate- and epoxy resin-based sealers. [PDF]

BMC Oral Health
Kandil NM, Elashiry MM, Wong B, Elgendy AA.   +3 more
europepmc   +1 more source

Experimental Characterization of Mycelium‐Based Composites Under Multiple Loading Conditions

Advanced Engineering Materials, EarlyView.
This study examines the mechanical response of mycelium‐based composites under compression, shear, and tension using mechanical testing and imaging methods. The comparison between unpressed and hot‐pressed specimens shows that hot pressing is associated with higher compression and shear stiffnesses.
Shaghayegh Elahi, Kimiya Tajik, Harvey Shaw, Matti Isakov, Sami Pajunen, Lauri Rautkari   +5 more
wiley   +1 more source

Microtensile bond strength and dentin-adhesive interface of universal adhesives before and after artificial aging: an in vitro study. [PDF]

Sci Rep
Santander-Rengifo F, Carreras-Presas CM, Cayo-Rojas C.   +2 more
europepmc   +1 more source

Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites

Advanced Engineering Materials, EarlyView.
This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim, Li Meng, Ahmad R. Najafi, Nicolas J. Alvarez   +3 more
wiley   +1 more source

Shear Bond Strength of a Light-Cured and a Dual-Cured Universal Adhesive to Primary and Permanent Dentin: An In Vitro Study. [PDF]

Biomimetics (Basel)
Fousekis E, Arhakis A, Arapostathis K, Mourouzis P, Tolidis K, Dionysopoulos D.   +5 more
europepmc   +1 more source

Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application

Advanced Engineering Materials, EarlyView.
N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang, Mayur Pole, Tingkun Liu, Kenneth A. Ross, Christopher B. Smith   +4 more
wiley   +1 more source

Influence of chemical conditioning and micromechanical roughening on bond strength to zirconia ceramic. [PDF]

BMC Oral Health
Khalil AA, Ellayeh M, Attia A.
europepmc   +1 more source

Experimental and Numerical Modal Analysis of Composite Sandwich Structures Using Surfboards as Model Systems

Advanced Engineering Materials, EarlyView.
This article presents an experimental and numerical modal investigation of composite sandwich structures using surfboards as model systems. By comparing different core materials and reinforcement strategies, the study demonstrates how local stiffeners influence vibrational response and introduce characteristic modal features, highlighting modal ...
Brett Connellan, Luca Lomazzi, Mathis Mercier, Kara Stark, Marc in het Panhuis   +4 more
wiley   +1 more source

Development of Remineralizing and Antibacterial Resin Coating for Provisional Crowns with Improved Bond Strength and Wear Resistance. [PDF]

Polymers (Basel)
Ba-Armah I, Alhussein A, Almutairi N, Alenizy M, Alqarni H, Altamimi Y, Altamimi A, Masri R, Sun J, Weir MD, Xu HHK.   +10 more
europepmc   +1 more source

Some Problems in Bond Strength and Effect of Filler on Bond Strength

Journal of the Japan Society of Colour Material, 1972
openaire   +2 more sources