Results 11 to 20 of about 189,008 (316)
Buildings, 2023 Titanium-clad (TC) bimetallic steel is an advanced composite steel consisting of metallurgically bonded titanium alloy and structural steel. This paper compared the high-cycle fatigue properties of three types of TC bimetallic steels, including two hot ...
Jianbo Jiang +3 more
doaj +1 more source
Reactive bonding and low temperature bonding of heterogeneous materials
, 2022 S.307-318This paper describes alternative low-temperature bonding procedures in Microsytems Technology. On the one hand reactive bonding is introduced, which is a relatively new joining technique for the mounting of microelectric components and the ...
Wünsch, Dirk +3 more
core +1 more source
Modeling and measuring the bonding strength of overmolded polymer parts
Polymer Testing, 2023 Overmolding a polymer onto a polymer substrate is a versatile plastic processing technique already widely used in industry and has a high potential to customize mass-produced polymer parts. Even though the industry is ready for this technology, there are
Anna Szuchács +2 more
doaj +1 more source
Evaluation of Ultrasonic Bonding Strength with Optoacoustic Methods
Applied Sciences, 2018 This study reports the application of an optoacoustic method for evaluating the bonding strength of ultrasonically bonded joints in a non-destructive and non-contact fashion.
Takumi Kamimura +2 more
doaj +1 more source
Optimization of Alkali Activator on the Strength Properties of Fly Ash Based Geopolymer Repair Materials [PDF]
Archives of Metallurgy and MaterialsFlexible and rigid road pavement deteriorates over time and needs high-performance patching repair materials. Cold mix asphalt patching is an easy and inexpensive repair material to repair potholes and other damaged roads.
W.W.A. Zailani +6 more
doaj +1 more source
Bond strength evaluation of the veneering-ceramics bonds [PDF]
Medicina Oral Patología Oral y Cirugia Bucal, 2010 The purpose of this study was to determine whether the bond of veneering porcelain to a ceramic core in bilayered ceramics was similar to that of the metal ceramic control of well known behaviour.Six groups of nine specimens each were fabricated, whose dimensions were 15 mm long and 8 mm in diameter at the core, and 2 mm long and 8 mm in diameter for ...
López Mollá, Victoria +4 more
openaire +5 more sources
Effects of Mechanical and Chemical Pretreatments of Zirconia or Fiber Posts on Resin Cement Bonding.
PLoS ONE, 2015 The bonding strength between resin cement and posts is important for post and core restorations. An important method of improving the bonding strength is the use of various surface pretreatments of the post. In this study, the surfaces of zirconia (fiber)
Rui Li +5 more
doaj +1 more source
A numerical study on thermal bonding with preheating technique for polypropylene microfluidic device
e-Polymers, 2023 This study presents a method for producing microfluidic chips from polypropylene using a pre-heated bonding area and thermal bonding technology. ANSYS was utilized to investigate the effects of bonding parameters and microchannel deformation and predict ...
Almezgagi Esam Abdulrahman +3 more
doaj +1 more source
In situ SEM study on tensile fractured behavior of Al/steel laser welding-brazing interface
Materials & Design, 2022 Microcracks initiated and propagated behaviors in Al/steel interface determined interfacial bonding strength and this was observed by in situ scanning electron microscopy (SEM) technology.
Hongbo Xia +8 more
doaj +1 more source
Characterization of dentine to assess bond strength of dental composites
, 2015 This study was performed to develop alternating dentine adhesion models that could help in the evaluation of a self-bonding dental composite. For this purpose dentine from human and ivory was characterized chemically and microscopically before and after ...
Bozec, L +13 more
core +1 more source