Results 211 to 220 of about 394,492 (288)

Polariton condensate far-detuned from exciton resonance in WS₂ bound states in the continuum. [PDF]

Nat Commun
Sung J, Kim J, Lee HS, Choi WH, Jeong M, Lee J, Kim S, Shin DJ, Choi D, Rho J, Gong SH, Song HG.   +11 more
europepmc   +1 more source

Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition

Advanced Engineering Materials, EarlyView.
A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley   +1 more source

Nonlinear light conversion and infrared photodetection with laser-printed plasmonic metasurfaces supporting bound states in the continuum. [PDF]

Light Sci Appl
Pavlov DV, Sergeeva KA, Seredin AA, Cherepakhin AB, Sergeev AA, Sokolova AV, Kulchin YN, Zhizhchenko AY, Petrov MI, Kuchmizhak AA, Rogach AL.   +10 more
europepmc   +1 more source

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

Advanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi, Hiroyuki Awano, Kenji Tanabe   +2 more
wiley   +1 more source

Near-field probing of the local density of optical states enhanced by bound states in the continuum in nonlocal metasurfaces. [PDF]

Nat Commun
Ji J, Sánchez-Gil JA, Peeters D, Holman W, Hoang TX, van Mechelen D, Gómez Rivas J.   +6 more
europepmc   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Nonreciprocal transmission based on quasi-bound states in the continuum via scaled lattice constants. [PDF]

Nanophotonics
Li R, Sun J.
europepmc   +1 more source

Characterization of a Recyclate‐Based MgO‐Steel Composite As‐Sintered Inert Anode Candidate After Exposure to Cryolite Electrolysis

Advanced Engineering Materials, EarlyView.
Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi, Alexander Adamczyk, Nora Brachhold, Gert Schmidt, Jana Hubálková, R. Gumeniuk, Alexandros Charitos, Christos G. Aneziris   +7 more
wiley   +1 more source

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

Advanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost, Lionel Presmanes, Soléna Colin, Marie Vidal, Sophie Guillemet‐Fritsch   +4 more
wiley   +1 more source