Results 161 to 170 of about 3,234,210 (272)

A Novel Approach to Estimate the Transition Temperature via Dynamic Nanoindentation

Advanced Engineering Materials, EarlyView.
A new dynamic nanoindentation‐based method was developed that uses the stiffness ratio as an indicator of the elastic–plastic deformation contributions at different temperatures. The approach successfully identified transition temperatures in ferritic steel and distinguished them from continuously ductile austenitic steel.
Stefan Zeiler, Nikolaus Kostwein, Ronald Schnitzer, Christian Mitterer, Verena Maier‐Kiener   +4 more
wiley   +1 more source

Droplets sitting on thin elastic sheets: a study with the boundary element method. [PDF]

Eur Phys J E Soft Matter
Sultan S, Grawitter J, Antunes GC, Stark H.   +3 more
europepmc   +1 more source

Cryogenic Deformation Behavior of TiAl and Insights Into Embrittlement After High‐Temperature Exposure Combined With Secondary Ion Mass Spectroscopy of Near Surface Chemistry

Advanced Engineering Materials, EarlyView.
Near‐surface deuterium enrichment profiles for different microstructural types of TiAl after exposure at 700 °C in a heavy water‐containing environment. The deuterium levels are significantly higher than expected from natural occurrence, indicating that the heavy water dissociated during the exposure treatment and entered the specimens.
Jonathan D. H. Paul, Alexander Welle, Dirk Matthiessen, Michael Oehring, Fritz Appel, Florian Pyczak   +5 more
wiley   +1 more source

Qualitative analysis and numerical simulation of ABC fractional impulsive differential systems with implicit nonlinear terms and integral boundary conditions. [PDF]

PLoS One
Sharif AA, Hamood M, Ghadle KP.
europepmc   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Vibration Characteristics of Alumina-Steel Axially Functionally Graded Fluid-Conveying Pipes: A Physics-Based GITT and MLP Surrogate Study. [PDF]

Materials (Basel)
Gao L, Gu J, Guo T, Zhao S, Li J.
europepmc   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

NPINN+: an enhanced physics-informed neural network for solving wave equations with nonlocal boundary conditions. [PDF]

Sci Rep
Tan Q, Yang S, Qin Y.
europepmc   +1 more source

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

Advanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel, Prashant K. Purohit, Jordan R. Raney   +2 more
wiley   +1 more source

Convergence of the Immersed Interface Method in Linear Elasticity. [PDF]

Mathematica (N Y)
Asghar S, Peng Q, Javierre E, Vermolen F.   +3 more
europepmc   +1 more source