Results 81 to 90 of about 241,347 (311)
β‐Catenin/c‐Myc Axis Modulates Autophagy Response to Different Ammonia Concentrations
Advanced Biology, Volume 9, Issue 3, March 2025.Ammonia, detoxified by the liver into urea and glutamine, impacts autophagy differently at varying levels. Low ammonia activates autophagy via c‐Myc and β‐catenin, while high levels suppress it. Using Huh7 cells and Spf‐ash mice, c‐Myc's role in cytoprotective autophagy is revealed, offering insights into hyperammonemia and potential therapeutic ...
S. Sergio +11 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
Electrical characteristics of top-down ZnO nanowire transistors using remote plasma ALD
Top-down fabrication is used to produce ZnO nanowires by remote plasma atomic layer deposition over a SiO2 pillar and anisotropic dry etching. Nanowire field-effect transistors (FETs), with channel lengths in the range of 1.3–18.6 µm, are then fabricated
Masaud, T.B. +9 more
core +1 more source
, 2010 Plasma electrolytic oxidation, or PEO, is a surface modification process for the production of ceramic oxide coatings upon substrates of metals such as aluminium, magnesium and titanium.
core +1 more source
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source
Degradation and Breakdown of W–La2O3 Stack after Annealing in N2 [PDF]
, 2008 We report the effect of relatively high-voltage stressing (under substrate injection) on the stress-induced leakage current (SILC) and breakdown of W–La2O3 stacked structures.
JOEL MOLINA REYES +2 more
core
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Impact of Nitridation on Bias Temperature Instability and Hard Breakdown Characteristics of SiON MOSFETs. [PDF]
Micromachines (Basel), 2023 Tyaginov S +12 more
europepmc +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
The suitability of N2 to replace SF6 in a triggered spark-gap switch for pulsed power applications
, 2009 The high dielectric strength of sulphur hexafluoride (SF6) when compared with other gases, coupled with safety benefits such as non-flammability and non-toxicity, has seen the widespread use of SF6 for the insulation of switching components. However, SF6
Timoshkin, I. +6 more
core