Results 1 to 10 of about 3,080,690 (333)
Effects of Curing Conditions on the Self-Healing of Geopolymer Paste [PDF]
MATEC Web of Conferences, 2023 Geopolymers are inorganic polymers produced by the reaction of aluminosilicates and alkaline solutions and show good mechanical and thermal features with a huge potential for use in the construction industry.
Ozen Meral Yildirim +3 more
doaj +1 more source
Study on the High-performance Composite Wall Panel Envelop of Building and its Relevant Joint Construction [PDF]
E3S Web of Conferences, 2020 Aiming at the general problems of envelop wall panel about the existing building, such as large surface density, low strength, poor service performance and high maintenance cost, a kind of high-performance composite wall panel is proposed in this paper ...
Gao Yuxin +5 more
doaj +1 more source
Effect of α: Phase Nano Al2O3 and Rice Husk Ash in Cement Mortar
Advances in Civil Engineering, 2022 The study focused on the investigation of the influence of α-phase nano Al2O3 (NA) and M-sand as a fine aggregate on the partial replacement of cement by micro rice husk ash (MRHA) to enhance the mechanical properties and durability of mortar and achieve
Alexander Gladwin Alex +3 more
doaj +1 more source
Japan Architectural Review, 2023 The deformation behavior of prestressed timber beams after a gap opens at the beam‐column interface is evaluated in this study using the compressive stress distribution along the beam length.
Takashi Shirayama +2 more
doaj +1 more source
Load-bearing Behaviour of Laminated Tempered Glass with Reground Edges
Challenging Glass Conference Proceedings, 2020 Designers use exposed glass edges to reach maximum transparency, for example within glass steps, glass beams or glass columns. These applications require mechanical finishing to achieve high optical quality and to compensate for the edge notch that ...
Maximilian Möckel +2 more
doaj +1 more source
Comparison of the Residual Stresses at the Edge and Surface of Thermally Toughened Glass
Challenging Glass Conference Proceedings, 2020 The strength of thermally toughened glass is regulated in EN 12150-1 for fully tempered glass (FTG) and EN 1863-1 for heat-strengthened glass (HSG). The manufacturer has to prove the strength by four-point bending tests based on EN 1288- 3. A measurement
Katharina Lohr +2 more
doaj +1 more source
Functionalization of the Fine Al2O3 Abrasive by the Polyacrylamide Deposition
Medžiagotyra, 2021 In order to enhance the dispersion stability of ultra-fine Al2O3 powder in aqueous media, the alumina particles were modified with silane coupling agent KH570 at first, and then 2,2'-Azobis(2-amidinopropane) dihydrochloride (AIBA) was anchored onto the ...
Pengfei MA +5 more
doaj +1 more source
Activity Patterns and Pollution Exposure
European Journal of Transport and Infrastructure Research, 2001 In recent times there has been increasing interest in modelling policies to limit impacts of air pollution due to motor vehicles. Impacts of air pollution on human health and comfort depend on the relationship between the distribution of pollutants and ...
Leorey Marquez +3 more
doaj +1 more source
Thermal mass and thermal comfort in offices – experimental studies of a concrete floor [PDF]
MATEC Web of Conferences, 2019 Previous studies demonstrated that the use of thermal mass in buildings can contribute to reduce the energy demand and improve the thermal comfort.
Grynning Steinar +3 more
doaj +1 more source
Measurements behind Internal Insulation on Solid Masonry Walls with Different Orientations and Degrees of Repair in a Danish Multi-story Building [PDF]
E3S Web of Conferences, 2020 Internal insulation is used in many heritage buildings to ensure a better indoor environment and reduce energy use. This article describes measurement results from installing an internal insulation system in a Danish multi-story building.
Vanhoutteghem Lies +2 more
doaj +1 more source