Results 41 to 50 of about 3,475 (257)

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

Advanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal, Michael M. Becker, Sarah C. L. Fischer   +2 more
wiley   +1 more source

Low‐Temperature Imidization of Polyimides (PI) for Scalable Manufacturing of Flexible Wearable Electronics

Advanced Engineering Materials, EarlyView.
Low‐temperature imidization of PEG‐modified polyimide enables fully screen‐printed, roll‐to‐roll fabrication of flexible electrodes on PET substrates, delivering robust mechanical durability and reliable ECG/EMG signal performance for wearable electronics.
Akib Abdullah Khan, Jong‐Hoon Kim
wiley   +1 more source

A Simplified Laminar Flow Model for the Pultrusion of Glass Fiber/Polyethylene Terephthalate Commingled Yarns

Advanced Engineering Materials, EarlyView.
A simplified thermoplastic pultrusion model is developed to predict thermal fields in glass fiber/polyethylene terephthalate (GF/PET) composites with reduced computational cost. By combining effective material homogenization, validation against literature data, and Gaussian‐process‐based optimization, the study reveals how heating limits, pulling speed,
Elder Soares, Nadège Bouchonneau, Christian Jochum, Donald Radford   +3 more
wiley   +1 more source

Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing

Advanced Engineering Materials, EarlyView.
The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai, Zeki Ayrildi, Buse Şen, Maik Rajkowski, Mathias Redondo Garcia, Markus Stricker, Guillaume Laplanche   +6 more
wiley   +1 more source

Molecular Dynamics Studies of Shape Memory Polymers: From Bead–Spring Models to Atomistic Simulations

Advanced Engineering Materials, EarlyView.
Coarse‐grained (left) and atomistic (right) models of the shape memory polymer ESTANE ETE 75DT3 are shown schematically. The two representations bridge molecular detail and mesoscopic description. Both models capture shape memory behavior, linking segmental mobility and conformational relaxation of anisotropic chains to macroscopic recovery, and ...
Fathollah Varnik
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Synthesis, properties and XPS analysis of Cu-, Ni-, Ti-based metallic glasses [PDF]

China Foundry, 2014
Metallic glasses (MG) represent an interesting group of materials as they possess outstanding physical, chemical and mechanical properties compared to their crystalline counterparts.
Qin Chunling, Wang Lijuan, Wang Zhifeng
doaj  

Extreme rejuvenation and softening in a bulk metallic glass

Nature Communications, 2018
Deforming metallic glasses can rejuvenate them to higher energy states, but only in the shear bands where deformation is usually concentrated. Here, the authors use a notched setup to suppress shear banding and promote significant bulk softening of a ...
J. Pan, Y. X. Wang, Q. Guo, D. Zhang, A. L. Greer, Y. Li   +5 more
doaj   +1 more source

Processability of Bulk Metallic Glasses [PDF]

American Journal of Applied Sciences, 2017
Microfluidic Shear Flow Instabilities in Injection Molded Glassy Metal are investigated. The formation of microfluidic shear flows instabilities involving the presence of different viscosities fluids has been observed in injection molded Bulk Metallic Glasses. The complex rheology of injection molded metastable glassy metal, which has been hypothesized
AVERSA, Raffaella, Parcesepe, Daniela, Petrescu, Relly Victoria V., Berto, Filippo, Chen, Guanying, Petrescu, Florian Ion T., Tamburrino, Francesco, APICELLA, Antonio   +7 more
openaire   +2 more sources

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source