Results 71 to 80 of about 1,102,576 (287)
Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy
Advanced Engineering Materials, EarlyView.Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang +6 more
wiley +1 more source
Fabrication Routes for Ionic Conducting Fiber Strain Sensors
Advanced Engineering Materials, EarlyView.Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw +3 more
wiley +1 more source
Large Compressive Plasticity in a La-Based Glass-Crystal Composite
Metals, 2012 La55Al25Cu10Ni10 metallic glass has been reinforced with 325-mesh Ta particles to obtain ex situ glass-crystal composites. The composites show a high compressive plasticity (40%) with a minor reduction (~8%) in yield strength—a combination unprecedented ...
Shantanu V. Madge +3 more
doaj +1 more source
Fracture Behaviors of Bulk Metallic Glasses Under Complex Tensile Loading
, 2017 Up to now the theoretical analysis for fracture behaviors of bulk metallic glasses (BMGs) are limited to uniaxial loading. However, materials usually suffer complex stress conditions in engineering applications.
Wang, TC +4 more
core +1 more source
Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning
Advanced Engineering Materials, EarlyView.The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley +1 more source
Estimation of Gibbs free energy difference in Pd-based bulk metallic glasses [PDF]
China Foundry, 2008 A new thermodynamic expression for Gibbs free energy difference ΔG between the under-cooled liquid and the corresponding crystals of bulk metallic glasses was derived.
Cai Anhui, Xiong Xiang, Liu Yong
doaj
Feasibility and Limitations of the Advanced Replica Process for Bioactive Glasses
Advanced Engineering Materials, EarlyView.Periodic 3D‐printed Kelvin‐cell templates enable a controlled advanced replica process for fabricating highly porous glass lattices. Across P45K9, 45S5, and 13–93, material‐dependent differences in coating, burnout, and shrinkage lead to distinct strut morphologies, while comparable final porosities of 83%–88% are retained.
Swantje Funk +4 more
wiley +1 more source
Micro-lateral extrusion of Zr55Cu30Al10Ni5 bulk metallic glass under low-frequency vibration loading
MATEC Web of Conferences, 2015 The effect of vibration on the micro-forming ability of Zr55Cu30Al10Ni5 bulk metallic glass in its supercooled liquid region was studied. The experiment of micro-extrusion was carried out under different amplitude (38 ∼ 760 N) and different frequency (0 ...
Li Jinyang +3 more
doaj +1 more source
Metals, 2016 In this study, the thermal and mechanical properties of Cu50−xZr43Al7Agx (x = 0, 3, 4, 5, 6) bulk metallic glasses (BMGs) are investigated by using an X-ray diffractometer (XRD), a differential scanning calorimeter (DSC), differential thermal analysis ...
Tsan-Man Chung +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe +6 more
wiley +1 more source