Results 81 to 90 of about 44,002 (237)

Insight into the Internal Structure of Biogenic, Synthetic and Geological Apatite by Electron Microscopy and X‐Ray Scattering

Advanced Functional Materials, EarlyView.
Apatite occurs in many forms in nature, e.g. in teeth and geological minerals. Internally, biological apatite contains nanocrystals that are also found in synthetically prepared calcium phosphate nanoparticles which are used in biomedicine, e.g. for gene and drug delivery and for bone regeneration. Abstract Calcium phosphate is the inorganic component (
Kathrin Kostka, Oleg Prymak, Kateryna Loza, Matthias Epple   +3 more
wiley   +1 more source

Microplastics from Wearable Bioelectronic Devices: Sources, Risks, and Sustainable Solutions

Advanced Functional Materials, EarlyView.
Bioelectronic devices (e.g., e‐skins) heavily rely on polymers that at the end of their life cycle will generate microplastics. For research, a holistic approach to viewing the full impact of such devices cannot be overlooked. The potential for devices as sources for microplastics is raised, with mitigation strategies surrounding polysaccharide and ...
Conor S. Boland
wiley   +1 more source

Tuning the Electronic Structure and Spin State of Fe─N─C Catalysts Using an Axial Oxygen Ligand and Fe Clusters for High‐Efficiency Rechargeable Zinc–Air Batteries

Advanced Functional Materials, EarlyView.
A FeN4─O/Clu@NC‐0.1Ac catalyst containing atomically‐dispersed FeN4─O sites (medium‐spin Fe2+) and Fe clusters delivered a half‐wave potential of 0.89 V for ORR and an overpotential of 330 mV at 10 mA cm−2 for OER in 0.1 m KOH. When the catalyst was used in a rechargeable Zn–air battery, a power density of 284.5 mW cm−2 was achieved with excellent ...
Yongfang Zhou, Yu Mao, Mengyao Chang, Ziyun Wang, Wenke Xie, Cuizhu Ye, Shanghai Wei, Lars Thomsen, Geoffrey I. N. Waterhouse   +8 more
wiley   +1 more source

Photo‐Switching Thermal and Lithium‐Ion Conductivity in Azobenzene Polymers

Advanced Functional Materials, EarlyView.
Light‐responsive azobenzene polymers control thermal and ionic transport simultaneously through structural transitions. UV illumination disrupts π–π stacking, converting crystalline trans states to amorphous cis configurations. Thermal conductivity drops from 0.45 to 0.15 W·m−1·K−1 while Li+ diffusivity increases 100 fold. This dual transport switching
Jaeuk Sung, Jungwoo Shin, Qiujie Zhao, Minjee Kang, Christopher Evans, Cecilia Leal, Paul V. Braun, David G. Cahill   +7 more
wiley   +1 more source

First aid and emergency treatment after hydrofluoric acid splash

Zdravniški Vestnik, 2010
Introduction: Chemicals are used in all kinds of industry and one fifth of workers have dealt with dangerous chemicals. Hydrofluoric acid (HF) is one of the most dangerous inorganic acids; it is used in the electronics, chemical, glass, steel, car and ...
Miran Brvar, Marija Jamšek, Martin Možina   +2 more
doaj  

Anomalous Stiffening of a Conjugated Polymer During Electrochemical Oxidation

Advanced Functional Materials, EarlyView.
The electromechanical response of a thienothiophene‐based conjugated polymer with triethylene glycol side chains is investigated. Electrochemical nanoindentation and atomic force microscopy reveal a modest and reversible increase in elastic modulus at room temperature upon electrochemical oxidation.
Judith Pons i Tarrés, Di Zhu, Chiara Musumeci, Youngseok Kim, Dilara Meli, Hang Yu, Meghna Jha, Bryan D. Paulsen, Ruiheng Wu, Joost Kimpel, Zachary Laswick, Sri Harish Kumar Paleti, Yadong Zhang, Stephen Barlow, Seth R. Marder, Jenny Nelson, Jonathan Rivnay, Christian Müller   +17 more
wiley   +1 more source

Associated bacterial and fungal infections in burn wounds: Common factors, distribution in etiology, age groups, bacterial and fungal strands – Evaluation of a single burn center experience of 20 years

Burns Open
Introduction: Burn intensive care unit (BICU) patients suffer from reduced immunological competence. Often bacterial and fungal infections occur as single or associated infection of the burn site.
Christian Weinand
doaj   +1 more source

Colloidal Crack Sintering Lithography for Light‐Induced Patterning of Particle Assemblies

Advanced Functional Materials, EarlyView.
Colloidal crack sintering lithography (CCSL) is a microfabrication technique that uses light‐induced photothermal heating to trigger sintering and controlled cracking in polymer colloidal assemblies. Local structural changes generate microchannels and patterns, enabling direct writing of diverse topographic motifs.
Marius Schoettle, Ariane V. Mader, Willem L. Noorduin   +2 more
wiley   +1 more source

Alkali Ion‐Incorporated HfO2 Dielectrics for Reconfigurable Neuromorphic Computing

Advanced Functional Materials, EarlyView.
This work presents an indium gallium zinc oxide (IGZO) transistor with an alkali cation‐integrated hafnium dioxide (HfO2) dielectric exhibiting synaptic behavior via ion retention. The solution‐based film fabrication strategy overcomes the limitations of atomic layer deposition (ALD) and precursor coating, enabling the control of synaptic retention ...
Seung Yeon Ki, In Cheol Kwak, Seonkwon Kim, Jihyun Kim, Dong Gue Roe, Se‐Jin Kim, Joohoon Kang, Jeong Ho Cho   +7 more
wiley   +1 more source

Interconnected Porous Hydrogels with Tunable Anisotropy Through Aqueous Emulsion Bioprinting

Advanced Functional Materials, EarlyView.
A 3D bioprintable microporous bioink is developed using an aqueous two‐phase system (ATPS) composed of extracellular matrix (ECM) mimetic biopolymers. The ATPS bioink enables the fabrication of interconnected porous architectures with up to 70% porosity, supporting long‐term cell viability and 3D cell alignment, enabling a simultaneous generation of ...
Hugo Edgar‐Vilar, Francisca P. Correia, Inês M. Freitas, Vítor M. Gaspar, João F. Mano   +4 more
wiley   +1 more source