Results 151 to 160 of about 211,509 (290)

Anti‐Slip Material‐Based Strategies and Approaches

Advanced Materials Technologies, EarlyView.
This review highlights the principle mechanisms of slipping at the microscale, linking contact mechanics with a friction behavior model for surface interfaces. Main strategies to develop anti‐slip properties to the surfaces are discussed alongside standardized testing approaches.
Sogand Abbaspoor‐Zanjani, Carlo Antonini, Teresa Gatti, Mengjiao Wang   +3 more
wiley   +1 more source

The Impact of Concomitant Traumatic Brain Injuries on the Surgical Treatment of Burns: A Long-Term, Monocentric Retrospective Study. [PDF]

J Burn Care Res
Vasella M, Pais MA, Naef L, Haenggi M, Brandi G, Keller E, Staartjes VE, Regli L, Giovanoli P, Kim BS, Vasella F.   +10 more
europepmc   +1 more source

Overcoming Printing and Interfacial Challenges in Liquid Metal Direct Writing for Integrated Stretchable Electronics

Advanced Materials Technologies, EarlyView.
Liquid metal direct writing is advanced from a technological and fundamental point. Utilizing a kinematic bed, printing on large surfaces with irregularities is enabled. Furthermore, a pressure‐driven flow during printing is discovered that affects the thickness of traces.
Maximilian Krack, Lennert Purnal, Parth Vinayakrao Sewlikar, Sam Cuyvers, Gus Geurts, Rathul Nengminza Sangma, Derese Desta, Dieter Reenaers, Bart Ruttens, Iris De Graeve, Tom Hauffman, Seppe Terryn, Bram Vanderborght, Michaël Daenen, Wim Deferme, Monika Rai   +15 more
wiley   +1 more source

Record High Polarization at 2 V and Imprint‐Free Operation in Superlattice HfO2‐ZrO2 by Proper Tuning of Ferro and Antiferroelectricity

Advanced Materials Technologies, EarlyView.
Low‐power ferroelectric capacitors, based on superlattice HfO2‐ZrO2 is reported. With proper tuning of ferro and antiferroelectricity, an imprint‐free high switchable polarization charge (2Pr of 76 µC/cm2) is obtained with 2MV/cm leading to linear analog weight update and non‐volatile retention, providing a design guideline for emerging non‐volatile ...
Xinye Li, Padma Srivari, Mari Honkanen, Turkka Salminen, Sayani Majumdar   +4 more
wiley   +1 more source

An Injectable Thermosensitive Chitosan/Astaxanthin/Ibuprofen Hydrogel Mitigates High-Voltage, Low-Current Electrical Burn Injury Through Inhibition of ROS-NF-κB Signaling-Mediated Inflammation. [PDF]

Pharmaceutics
Yang X, Wang H, Zhang W, Gao P, Yu X, Qing W, Deng P, Li J, Luo Y, Tian L, Xie J, Chen M, Yu Z, Pi H, Liu T, Luo S.   +15 more
europepmc   +1 more source

End‐to‐End Sensing Systems for Breast Cancer: From Wearables for Early Detection to Lab‐Based Diagnosis Chips

Advanced Materials Technologies, EarlyView.
This review explores advances in wearable and lab‐on‐chip technologies for breast cancer detection. Covering tactile, thermal, ultrasound, microwave, electrical impedance tomography, electrochemical, microelectromechanical, and optical systems, it highlights innovations in flexible electronics, nanomaterials, and machine learning.
Neshika Wijewardhane, Lyn I. Jones, Richard M. Martin, Helen Winter, Faezeh Arab Hassani   +4 more
wiley   +1 more source

Delayed Urethral Stricture Following Remote Electrocution: A Case Report. [PDF]

Cureus
Akjay A, Ettoumi N, Ettoumi N, Jmil N, Bidan S, Nguema LD, El Anzaoui J.   +6 more
europepmc   +1 more source

Large‐Scale and Cost‐Effective Fabrication of Ultra‐Thin, Biodegradable Microelectrode Arrays and Pressure Sensors Using Laser Micromachining

Advanced Materials Technologies, EarlyView.
A mask‐free and cost‐effective UV‐pico‐second laser‐based microfabrication method is proposed to fabricate large‐area biodegradable microelectrode arrays and pressure sensors. These devices demonstrate low impedance, good conformability, excellent biocompatibility, and rapid degradation, providing a new route for next‐generation transient electronics ...
Bhavani Prasad Yalagala, Asfand Tanwear, María Cerezo‐Sánchez, Hossein Parvizi, Morteza Amjadi, Hadi Heidari   +5 more
wiley   +1 more source

Electrical Burns

Annals of Surgery, 1961
openaire   +3 more sources

3D Printed PEDOT:PSS‐Based Lattice Pressure Sensors With Tunable Electromechanical Response

Advanced Materials Technologies, EarlyView.
poly(3,4‐ethylenedioxythiophene): polystyrene sulfonate (PEDOT:PSS)‐based architected lattices are fabricated via single‐step Digital Light Processing (DLP) printing for tunable pressure sensing. Structural design variations allow precise control of sensitivity and range, while integrated conductivity eliminates post‐processing.
Ozan Karakaya, Naroa Lopez‐Larrea, Ali Veysel Tunc, Mikel Rincon‐Iglesias, Karin J. Chen, Katja Nau, Senentxu Lanceros‐Mendez, David Mecerreyes, Miryam Criado‐Gonzalez, Gerardo Hernandez‐Sosa   +9 more
wiley   +1 more source