Results 151 to 160 of about 92,840 (303)

Recent Advances in Conductive Rubber Composites: Progress, Challenges, and Emerging Opportunities

Macromolecular Rapid Communications, EarlyView.
This study reviews the recent advances in conductive rubber composites, focusing on key aspects such as material selection, conductive mechanisms, interfacial engineering, processing methods, vulcanization strategies, and practical applications. It also discusses current challenges and highlights emerging directions that are shaping the development of ...
Lu Yin, Ali Vahidifar, Steven Yu, Boxin Zhao   +3 more
wiley   +1 more source

Correction to "Capturing the Elusive Curve-Crossing in Low-Lying States of Butadiene With Dressed TDDFT". [PDF]

J Phys Chem Lett
Dar DB, Maitra NT.
europepmc   +1 more source

Enhancing the Performance of 3D‐Printed Polyamide Composites Through Pre‐ and Post‐Processing Methods

Polymer Composites, EarlyView.
FDM‐printed polyamide composites and post‐processing by annealing. ABSTRACT In this study, composite filaments with a short carbon fiber (CF) reinforced polyamide 612 (PA612) were produced using the FDM method at three different raster angles (0°, ±45°, 90°).
Busra Eyri, Yusuf Yagci, N. Gamze Karsli, Taner Yilmaz   +3 more
wiley   +1 more source

Preparation and Properties of Reprocessable Hydrogenated Styrene-Butadiene Rubber. [PDF]

Polymers (Basel)
Li T, Pan C, Yue D.
europepmc   +1 more source

Enhancing the Properties of PA6 and PA6/Ionomer Scraps Blend With CaCO3 Nanoparticles: Rheological, Mechanical, Thermal, and Morphological Evaluation

Polymer Engineering &Science, EarlyView.
ABSTRACT This study investigated the effects of incorporating ionomer scraps and CaCO3 nanoparticles on the rheological, mechanical, thermal, and morphological properties of neat polyamide 6 (PA6) and a PA6/ionomer scraps (80/20) blend. The ionomer formed an immiscible dispersed phase within the PA6, acting as an impact modifier; however, it reduced ...
Roberto Alves Taveira Jr., Patrícia Schmid Calvão, Adriana Martinelli Catelli Souza   +2 more
wiley   +1 more source

Chemical Fingerprinting of Synthetic Polymers via Direct Insertion Probe Mass Spectrometry. [PDF]

Macromolecules
Nissinen VH, Heilala N, Grönlund K, Auvinen P, Suvanto M, Saarinen JJ, Jänis J.   +6 more
europepmc   +1 more source

Enhancing the Tribological Performance of PLA via Process‐Induced Functional Grading in Masked Stereolithography

Polymer Engineering &Science, EarlyView.
An exposure‐time‐controlled MSLA fabrication strategy enabling filler‐free functionally graded polymers, resulting in up to a 62% reduction in specific wear rate. ABSTRACT Masked stereolithography (MSLA) enables high‐resolution fabrication of photopolymer components; however, the limited tribological performance of neat resins restricts their ...
Muhammet Mevlüt Karaca, Abdurrahim Temiz, Fatih Huzeyfe Öztürk   +2 more
wiley   +1 more source

Urinary metabolites of 1,3-butadiene, benzene and toluene and colorectal cancer incidence: a clinical case-control study. [PDF]

Cancer Causes Control
DuPre N, Babarinde O, Adhikari J, Lorkiewicz P, Krivokhizhina T, Gaskins J, Salazar-Guzman L, Jin A, Kavalukas S.   +8 more
europepmc   +1 more source

Pretreatment Effects of Conventional and Reactive Extrusion on LLDPE Waste Pyrolysis

Polymer Engineering &Science, EarlyView.
Schematic overview of the pyrolysis study using original and pretreated LLDPE waste samples. Pretreatment was performed via twin‐screw extrusion at 450°C: without additives (REX), with peroxide (REX‐RO2), or with polypropylene (REX–PP). All four samples underwent pyrolysis at 450°C–475°C for 15–45 min.
Yasmin Fialho Siqueira, Débora M. V. Miranda, Larissa L. A. Carvalho, Natasha K. Sitton, Ana Paula de Azeredo, Regina F. Nonemacher, Raquel S. Mauler, Luiz Eduardo P. Borges, José Carlos Pinto   +8 more
wiley   +1 more source

Enantioselective Butadiene-Mediated Aldehyde Crotylation of Alcohol Proelectrophiles: RuHCl(CO)(PPh₃)₃ as a Precatalyst. [PDF]

Org Lett
Santana CG, Pfaffinger DE, Meares PW, Krische MJ.   +3 more
europepmc   +1 more source