Results 11 to 20 of about 3,069,221 (295)

Jet Energy Calibration in the CMS experiment

open access: yesEPJ Web of Conferences, 2013
Jet reconstruction and calibration in the CMS experiment are complicated by the nonlinear response of the calorimeters and high pileup conditions. These difficulties are mitigated at CMS by utilising the particle flow approach. The jet energy calibration
Rathjens Denis   +3 more
doaj   +3 more sources

Energy Calibration Of The Gerda Experiment

open access: yes, 2018
GERDA has been designed to search for neutrinoless double beta decay of Ge76. Ge76 decays with the emission of two electrons and two antineutrinos, with a Q-value of 2039 keV. If neutrinos are Majorana particles, the two emitted antineutrinos can annihilate, with the signature of the decay being a sharp peak at the Q-value, whose width is determined by
MINGAZHEVA, Rizalina (8361030)   +1 more
openaire   +3 more sources

Calibration of the photon spectrometer PHOS of the ALICE experiment [PDF]

open access: yes, 2019
The procedure for the energy calibration of the high granularity electromagnetic calorimeter PHOS of the ALICE experiment is presented. The methods used to perform the relative gain calibration, to evaluate the geometrical alignment and the corresponding
Haque M. R.   +999 more
core   +12 more sources

Application of the Bootstrap to Calibration Experiments [PDF]

open access: yesAnalytical Chemistry, 1996
In calibration experiments, a number of samples of known concentration are used to establish the relationship between a measured response and sample concentration; this relationship is then used to estimate the unknown concentration of further samples from their measured responses. In addition to the estimates themselves, it is useful to have available
G, Jones   +4 more
openaire   +2 more sources

Bootstrapping in Controlled Calibration Experiments [PDF]

open access: yesTechnometrics, 1999
We consider the detennination of an unknown quantity-for example, the concentration of a particular chemical in a given sample or samples-using controlled calibration. Here several samples are prepared with concentrations chosen to cover a required range, and these are used to establish the relationship between concentration and the measured response ...
Jones, Geoffrey, Rocke, David
openaire   +3 more sources

A Novel Calibration Board and Experiments for 3D LiDAR and Camera Calibration [PDF]

open access: yesSensors, 2020
Aiming at the problems of feature point calibration method of 3D light detection and ranging (LiDAR) and camera calibration that are calibration boards in various forms, incomplete information extraction methods and large calibration errors, a novel calibration board with local gradient depth information and main plane square corner information (BWDC ...
Huaiyu Cai   +4 more
openaire   +4 more sources

Error Modeling and Experimental Study of a Flexible Joint 6-UPUR Parallel Six-Axis Force Sensor

open access: yesSensors, 2017
By combining a parallel mechanism with integrated flexible joints, a large measurement range and high accuracy sensor is realized. However, the main errors of the sensor involve not only assembly errors, but also deformation errors of its flexible leg ...
Yanzhi Zhao   +4 more
doaj   +1 more source

A High Performance Piezoelectric Sensor for Dynamic Force Monitoring of Landslide

open access: yesSensors, 2017
Due to the increasing influence of human engineering activities, it is important to monitor the transient disturbance during the evolution process of landslide. For this purpose, a high-performance piezoelectric sensor is presented in this paper.
Ming Li   +4 more
doaj   +1 more source

Absolute optical calibration using a simple tungsten light bulb: Experiment [PDF]

open access: yes, 2003
Absolute spectral intensity calibration of optical detectors has always been difficult. Up to now it was only possible through the use of expensive sources, which are cross-calibrated against national standards.
Mäkinen, S.   +3 more
core   +2 more sources

A Novel Two-Axis Load Sensor Designed for in Situ Scratch Testing inside Scanning Electron Microscopes

open access: yesSensors, 2013
Because of a lack of available miniaturized multiaxial load sensors to measure the normal load and the lateral load simultaneously, quantitative in situ scratch devices inside scanning electron microscopes and the transmission electron microscopes have ...
Chengli Shi   +4 more
doaj   +1 more source

Home - About - Disclaimer - Privacy