Results 21 to 30 of about 20,110 (217)

Toward High Throughput Core-CBCM CMOS Capacitive Sensors for Life Science Applications: A Novel Current-Mode for High Dynamic Range Circuitry

open access: yesSensors, 2018
This paper proposes a novel charge-based Complementary Metal Oxide Semiconductor (CMOS) capacitive sensor for life science applications. Charge-based capacitance measurement (CBCM) has significantly attracted the attention of researchers for the design ...
Saghi Forouhi   +2 more
doaj   +1 more source

Readout Circuits for Capacitive Sensors

open access: yesMicromachines, 2021
The development of microelectromechanical system (MEMS) processes enables the integration of capacitive sensors into silicon integrated circuits. These sensors have been gaining considerable attention as a solution for mobile and internet of things (IoT)
Yongsang Yoo, Byong-Deok Choi
doaj   +1 more source

DISCHARGE IN GAS BUBBLES IN WATER AS A SOURCE OF AN INTENSIVE FACTORS’ COMPLEX FOR WATER DISINFECTION: COMPARISON EXPERIMENTAL AND COMPUTER MODELLING RESULTS

open access: yesТехнічна електродинаміка, 2022
Computer simulation of the discharge process in an electric circuit, which contains a pulsed electric in gas bubbles in water, has been perf0rmed. The experimental oscillograms of voltage pulses are compared with the results of computer simulation of ...
М.І. Бойко, А.В. Макогон
doaj   +1 more source

An Improved LCL-L Compensation Topology for Capacitive Power Transfer in Electric Vehicle Charging

open access: yesIEEE Access, 2020
This paper proposes an LCL-L compensation circuit for high power capacitive power transfer (CPT) aiming at minimizing number of resonant components and improving system performance.
Van-Binh Vu   +3 more
doaj   +1 more source

A False Trigger-Strengthened and Area-Saving Power-Rail Clamp Circuit with High ESD Performance

open access: yesMicromachines, 2023
A power clamp circuit, which has good immunity to false trigger under fast power-on conditions with a 20 ns rising edge, is proposed in this paper. The proposed circuit has a separate detection component and an on-time control component which enable it ...
Boyang Ma   +7 more
doaj   +1 more source

Research and Optimization of High-Performance Front-End Circuit Noise for Inertial Sensors

open access: yesSensors
An inertial sensor is a crucial payload in China’s Taiji program for space gravitational wave detection. The performance of the capacitive displacement sensing circuit in the low-frequency band (0.1 mHz to 1 Hz) is extremely important because it directly
Yuzhu Chen   +7 more
doaj   +1 more source

Noise-Resistant CECG Using Novel Capacitive Electrodes

open access: yesSensors, 2020
For years, capacitive electrocardiogram (CECG) has been known to be susceptible to ambient interference. In light of this, a novel capacitive electrode was developed as an effective way to reduce the interference effect.
Chi-Chun Chen   +2 more
doaj   +1 more source

Capacitive Pressure Sensor With Integrated Signal-Conversion Circuit for High-Temperature Applications

open access: yesIEEE Access, 2020
In this paper, a capacitive pressure sensor for high-temperature application is proposed. This sensor includes three parts: a capacitive pressure-sensitive chip fabricated from green tapes using lamination technology, a C-V conversion circuit fabricated ...
Chen Li   +5 more
doaj   +1 more source

Contactless Interrogation System for Capacitive Sensors with Time-Gated Technique

open access: yesProceedings, 2017
This paper presents a measurement technique and system for the contactless interrogation of capacitive sensors via electromagnetic coupling. The interrogation unit employs a primary coil to periodically excite the capacitive sensor connected to a ...
Mehedi Masud   +4 more
doaj   +1 more source

Tailored Hierarchical Porous Copper Architectures via Three Dimensional Printing and Pressure‐less Sintering for Next‐Generation Lithium‐Metal Batteries

open access: yesAdvanced Engineering Materials, EarlyView.
A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley   +1 more source

Home - About - Disclaimer - Privacy