Results 61 to 70 of about 82,131 (349)
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Chemosensors, 2023 Electronic skin (e-skin) has the potential to detect large-scale strain, which is typically achieved by integrating multiple strain sensors into an array.
Song Wang +9 more
doaj +1 more source
Validation of Finite Element Modelling of Multielectrode Capacitive System for Process Tomography Flow Imaging [PDF]
, 1993 Finite element modelling of process tomography sensor systems is necessary for their CAD both for performance evaluation and design optimization. This paper involves the validation of finite element models of a 12-electrode capacitive sensor system for ...
Abdullah, F., Khan, S.
core
Electronic and Acoustic Engineering, 2020 Метою даної роботи є дослідження можливості використання ємнісного датчика як пристрою, що фіксує присутність людини у приміщенні при проектуванні систем енергозбереження; визначити його основні параметри та способи застосування. У роботі досліджено ємнісний датчик, робота якого основана на чутливості до зміни діелектричної проникності середовища, у ...
Andrii Viktorovych Melnyk +1 more
openaire +3 more sources
Fatigue Crack Initiation and Growth in Nanocrystalline Ni at Multiple Length‐Scales
Advanced Engineering Materials, EarlyView.Overview of miniaturized in situ SEM fatigue setup and resultant fatigue crack growth data for nanocrystalline Ni. The presented study focuses on the analysis of fatigue crack growth rate (FCGR) in focused ion beam‐notched microcantilevers prepared from nanocrystalline (NC) Ni as a model material.
Igor Moravcik +7 more
wiley +1 more source
A Full Textile Capacitive Woven Sensor
Advanced Materials Technologies, 2022 AbstractIn this paper, a full textile capacitive woven sensor integrated over a textile substrate is presented. The sensor consists in an interdigitated capacitance prepared to measure moisture and/or presence detection. In order to evaluate the sensor response to moisture, capacitance has been measured by means of an LCR meter from 20 Hz to 20 kHz in ...
Martínez Estrada, Marc +3 more
openaire +3 more sources
Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment
Advanced Engineering Materials, EarlyView.This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
Sensors, 2018 This paper proposes a novel charge-based Complementary Metal Oxide Semiconductor (CMOS) capacitive sensor for life science applications. Charge-based capacitance measurement (CBCM) has significantly attracted the attention of researchers for the design ...
Saghi Forouhi +2 more
doaj +1 more source
Target Mass Monitoring and Instrumentation in the Daya Bay Antineutrino Detectors
, 2013 The Daya Bay experiment measures sin^2 2{\theta}_13 using functionally identical antineutrino detectors located at distances of 300 to 2000 meters from the Daya Bay nuclear power complex. Each detector consists of three nested fluid volumes surrounded by
+27 more
core +1 more source