Results 61 to 70 of about 4,126,459 (396)
Application status and prospect of low carbon technology in iron and steel industry
工程科学学报, 2022 China proposes to achieve carbon peaking and carbon neutralization by 2030 and 2060, respectively. As a heavily carbon-based fuel industry, the carbon dioxide emission of the iron and steel industry is lower than that of the power and transportation ...
Yi XING +7 more
doaj +1 more source
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur +5 more
wiley +1 more source
Al–Si alloyed uncoated hot stamping steels for enhanced oxidation resistance
Journal of Materials Research and TechnologyHot stamping steels are extensively used in the production of lightweight automobile bodies, which are crucial for reducing carbon emissions. Although significant advancements have been made in the development of Si–Cr alloyed uncoated hot stamping ...
Zhaoqi Song +10 more
doaj +1 more source
Advances in Materials Science and Engineering, 2020 In order to research the effect of heat treatment on the microstructure and corrosion resistance of stainless/carbon steel bimetal plate, the annealing process at 700°C with different times was carried out for stainless/carbon steel bimetal plate ...
Hao Li +3 more
doaj +1 more source
Evaluation of Toughness of High Strength Low Alloy (HSLA) Steels as a Function of Carbon Content [PDF]
, 2019 The influence of carbon content on the microstructure and toughness of HSLA steel at room temperature was investigated based on experimental work and literature.
Naher, S., Qaban, A.
core
Using Taguchi method to optimize welding pool of dissimilar laser welded components [PDF]
, 2008 In the present work CO2 continuous laser welding process was successfully applied and optimized for joining a dissimilar AISI 316 stainless steel and AISI 1009 low carbon steel plates. Laser power, welding speed, and defocusing distance combinations were
A.G. Olabi +16 more
core +1 more source
Estimation of specific cutting energy in an S235 alloy for multi-directional ultrasonic vibration-assisted machining using the Finite Element Method [PDF]
, 2020 The objective of this work is to analyze the influence of the vibration-assisted turning process on the machinability of S235 carbon steel. During the experiments using this vibrational machining process, the vibrational amplitude and frequency of the ...
Florez García, Luis Carlos +2 more
core +2 more sources
Advanced Engineering Materials, EarlyView.Freeze‐drying of layered silicate is the key to get coatings with superior gas barrier. Freeze‐drying of layered silicates modified with dodecylamine (DDA) is a highly effective technique for the preparation of barrier pigments that significantly mitigate the permeation of oxygen, water vapor, and hydrogen through polymer films containing these ...
Joshua Lommes +4 more
wiley +1 more source
Journal of Materials Research and TechnologyThe austenite-to-martensite phase transformation plays a crucial part in the microstructure evolution of steel, with the morphology and grain size of martensite being key factors that influence the mechanical properties. This study explores the influence
Kaiyang Wang +9 more
doaj +1 more source
Evolution Law of Microstructure and Properties during Hot-rolling Process of Ultra-high-strength 92Si Wire Rod for Bridge Cables [PDF]
TeshugangAccording to the evolution law of microstructure and properties during the entire hot rolling process of ultra-high strength 92Si wire rod， methods such as mechanical property testing and microstructure characterization were used to analyze the ...
Li Yang, Liu Jinyuan, Xu Kai, Chen Dianqing, Pan Xiaokun, Zhang Chaolei
doaj +1 more source