Results 211 to 220 of about 3,055 (262)
Some of the next articles are maybe not open access.
Radiation curing of methacryloyloxyalkyl carbonates
Journal of Polymer Science: Polymer Chemistry Edition, 1983AbstractThe results of studying the radiation curing of methacryloyloxyalkyl carbonates (MC), a new type of oligomer, are presented. These oligomers are notable for their high rates of radiation curing. The radiation yield G(–M) is 2 × 105 for MC and 2 × 104 for triethylene glycol dimethyacrylate.
I. M. Barkalov +2 more
openaire +1 more source
Curing kinetics and curing process of phenolic impregnated carbon ablator
Journal of Applied Polymer Science, 2017ABSTRACTPhenolic impregnated carbon ablator (PICA), which is composed of the phenolic resin (PR) and carbon fiber, is of particular interest to researchers in the aerospace field. In this work, PICA was prepared by the double‐stage isothermal heating curing.
Ye Tian, Haiming Huang, Xiaoliang Xu
openaire +1 more source
Carbonation Curing versus Steam Curing for Precast Concrete Production
Journal of Materials in Civil Engineering, 2012AbstractAn investigation was conducted into the beneficial utilization of captured CO2 for early-age curing of precast concrete products. The performance of the carbonation-cured concrete was compared to that of steam curing to investigate the possibility of replacing steam curing with carbonation.
Vahid Rostami +2 more
openaire +1 more source
Pseudo-dynamic carbonation for concrete curing and carbon storage
International Journal of Materials and Structural Integrity, 2015Concrete demonstrates the capacity to absorb carbon dioxide. The reaction between concrete and carbon dioxide accelerates concrete curing at early age and converts CO2 into calcium carbonate for carbon storage. As-captured flue gas without recovery can be directly used in this application.
Yixin Shao +2 more
openaire +1 more source
The cure optimisation of carbon/epoxy prepregs
Composites Science and Technology, 1998A complete package of knowledge and numerical simulation of cure cycles has been developed and perfected for high-performance composite materials. The various constraints of an industrial process are respected and an optimizing temperature order is determined for oven and/ or autoclave control.
Marc LeGrand, Véronique Bellenger
openaire +1 more source
Radiation curing of carbon fibre composites
Radiation Physics and Chemistry, 2014Epoxy/carbon fibre reinforced composites were produced by means of e-beam irradiation through a pulsed 10 MeV electron beam accelerator. The matrix consisted of a difunctional epoxy monomer (DGEBA) and an initiator of cationic polymerisation, while the reinforcement was a unidirectional high modulus carbon fibre fabric.
G. Spadaro +6 more
openaire +1 more source
Effects of curing upon carbonation of concrete
Construction and Building Materials, 1995Abstract Even if mix design (cement content, W/C ratio) has an effect on durability of concrete mixed with blended cement, curing conditions, particularly curing time, also affect concrete durability against carbonation. The choice of curing time depends on cement content, and must be adjusted to concrete design (28 day strength, W/C ratio ...
J.P. Balayssac +2 more
openaire +1 more source
Curing Losses in Vuggy Carbonate Formations
SPE/IADC Middle East Drilling Technology Conference and Exhibition, 2018Abstract Despite the preventive wellbore strengthening (WBS) approach, lost circulation (LC) followed by well control events have been encountered where thousands of barrels of mud were lost to a formation resulting in long periods of shutdowns.
G. D. Alshubbar, R. Nygaard
openaire +1 more source
Efficient Curing of Vinyl Carbonates by Thiol‐Ene Polymerization
Macromolecular Rapid Communications, 2012Abstract Vinyl carbonates have recently been identified as a suitable alternative to (meth)acrylates, especially due to the low irritancy and cytotoxicity of these monomers. The drawback of some vinyl carbonates containing abstractable hydrogens arises through their moderate reactivity compared with acrylates.
Andreas, Mautner +6 more
openaire +2 more sources
Concrete carbonation as influenced by curing regime
Cement and Concrete Research, 1988Abstract The paper discusses the results of accelerated tests carried out to investigate the effects of using different curing regimes on the rate of concrete carbonation. Concrete prisms were made and cured in water and/or air for different periods of time. The prisms were then placed in a chamber filled continuously with carbon dioxide gas.
openaire +1 more source

