Results 181 to 190 of about 7,256,298 (291)

Mechanochemical Synthesis and Characterization of Nanostructured ErB4 and NdB4 Rare‐Earth Tetraborides

open access: yesAdvanced Engineering Materials, Volume 27, Issue 6, March 2025.
ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur   +5 more
wiley   +1 more source

Disparities in Advance Care Planning: Did COVID-19 Change Anything? [PDF]

open access: yesJ Am Geriatr Soc
Gangavati A   +14 more
europepmc   +1 more source

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

open access: yesAdvanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios   +5 more
wiley   +1 more source

The Shared Document as a Tool for Shared Care Planning: A Retrospective Analysis of 160 Cases. [PDF]

open access: yesHealthcare (Basel)
Masilla SS   +6 more
europepmc   +1 more source

Density Measurement of Irradiated and Nonirradiated Zirconium Oxide by Ptychographic X‐Ray Computed Tomography (PXCT)

open access: yesAdvanced Engineering Materials, EarlyView.
Mass density governs the protective behavior of oxide layers on nuclear fuel cladding. Ptychographic X‐ray computed tomography measures zirconium oxide grown on Zircaloy‐4 under reactor and autoclave conditions, revealing nearly identical bulk densities of 5.1 ± 0.80 g cm−3.
Okan Yetik   +9 more
wiley   +1 more source

Investigating the Effect of Inclination Angle and the Influence of Scan Parameters on the Appearance and Thermal and Mechanical Properties of Filigree Tension Rods of LPBF‐Manufactured NiTi Shape‐Memory Alloys

open access: yesAdvanced Engineering Materials, EarlyView.
This article investigates the dependence of the properties on the manufacturing orientation in the form of the inclination angle to the build plate of LPBF‐fabricated NiTi rods with a diameter of 150–220 µm. Metallographic, chemical, thermal, and mechanical characterization show behavior under identical manufacturing conditions that ranges from ...
Sandra Herzig   +2 more
wiley   +1 more source

Long-Term Care Planning and Sustainability of the Care System in the Region. [PDF]

open access: yesHealthcare (Basel)
Rajer C, Bogataj D, Bogataj M, Drobne S.
europepmc   +1 more source

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

open access: yesAdvanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel   +2 more
wiley   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

open access: yesAdvanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar   +3 more
wiley   +1 more source

Home - About - Disclaimer - Privacy