Results 31 to 40 of about 23,476 (260)

The Effect of Aluminium on Graphitization of Cast Iron Treated with Cerium Mixture

open access: yesArchives of Foundry Engineering, 2014
The work determined the influence of aluminium in the amount from about 0.6% to about 8% on graphitization of cast iron with relatively high silicon content (3.4%-3.9%) and low manganese content (about 0.1%).
Soiński M. S.   +3 more
doaj   +1 more source

Structural and Phase Analysis of the Ausferritic Ductile Cast Iron Matrix Obtained by Heat Treatment and in the Raw State

open access: yesC
This paper presents a comparative analysis of ausferritic ductile cast iron matrix obtained through heat treatment and in its raw state. Ausferrite without heat treatment was achieved by modifying the chemical composition, while nodular graphite was ...
Leszek Klimek   +4 more
doaj   +1 more source

Colour Metallography of Cast Iron - Chapter 3: Spheroidal Graphite Cast Iron (Ⅳ) [PDF]

open access: yesChina Foundry, 2010
Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc.
Zhou Jiyang
doaj  

Colour Metallography of Cast Iron - Chapter 4: Vermicular Graphite Cast Iron (Ⅰ) [PDF]

open access: yesChina Foundry, 2011
Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc.
Zhou Jiyang
doaj  

Failures of the Cast-Iron Columns of Historic Buildings—Case Studies

open access: yesInfrastructures, 2020
Selected technical problems related to the rehabilitation of cast-iron columns in structures from the turn of the 19th and 20th century are discussed in the paper. Lack of contemporary standard regulations related to the design of cast-iron structures is
Michał Gołdyn, Tadeusz Urban
doaj   +1 more source

Colour Metallography of Cast Iron - Chapter 3: Spheroidal Graphite Cast Iron (Ⅲ) [PDF]

open access: yesChina Foundry, 2010
Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc.
Zhou Jiyang
doaj  

Thermomechanical Fatigue and Creep–Fatigue Interaction of Inconel 718 Additively Manufactured by Laser Beam Powder Bed Fusion

open access: yesAdvanced Engineering Materials, EarlyView.
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth   +6 more
wiley   +1 more source

Colour Metallography of Cast Iron - Chapter 5: White Cast Iron (Ⅰ) [PDF]

open access: yesChina Foundry, 2011
Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc.
Zhou Jiyang
doaj  

Cast iron promises

open access: yesJournal of Innovation in Health Informatics, 2007
During the Victorian era, a fiercely competitive industry emerged to build and operate Britain's railways. Many of the design and construction skills required were still fairly rudimentary, and were typically developed through practical experience. The resulting mix of entrepreneurship and new technology reshaped the landscape, but often in ways which ...
openaire   +4 more sources

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

open access: yesAdvanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati   +11 more
wiley   +1 more source

Home - About - Disclaimer - Privacy