Results 31 to 40 of about 147 (134)

Influence of Fat Oil Binding Capacity on Shelf‐Life and Consumer Acceptance of a Chocolate‐Based Model System

Journal of the American Oil Chemists' Society, EarlyView.
ABSTRACT In chocolate‐coated products, oil migration can lead to chocolate softening and discoloration, filling hardening, and reduced consumer acceptance. This study examined three fats (soy‐, palm‐, and palm‐kernel (PK) based), crystallized under different conditions (cooling rate and high intensity ultrasound (HIU)) with differing oil binding ...
Audrey Lidgard, Farnaz Maleky, Silvana Martini   +2 more
wiley   +1 more source

Study on the Fire Resistance of Castellated Composite Beams with Semi-Rigid Restraints

Buildings
To study the fire resistance of castellated composite beams with semi-rigid restraints, temperature rise tests with constant loads were performed on two full-scale castellated composite beams with circular holes and semi-rigid restraints to compare the ...
Zongxuan Zhang, Junli Lyu, Guixin Shi, Wenhao Li, Chen Wang   +4 more
doaj   +1 more source

Nanofiber PVA‐Based Membranes Incorporating Functionalized Spanish Broom Derivatives for Sustainable Water Purification

ENERGY &ENVIRONMENTAL MATERIALS, EarlyView.
This study investigates Spanish broom (Spartium junceum) as a renewable source for electrospun composite membranes in sustainable water purification. MCC and biochar were functionalized with eco‐friendly precursors and nanomaterials (i.e., HNT, β‐CDs) to develop hybrid PVA nanofiber composites.
Giulia Rando, Silvia Sfameni, Jozefien Geltmeyer, Alessandra Palella, Lorenzo Spadaro, Alberto Riminucci, Karen De Clerck, Maria Rosaria Plutino   +7 more
wiley   +1 more source

Optimization Parameter of Openings with Diagonal Stiffeners on Laterally Brace Castellated Steel Beams

Jurnal Ilmiah Teknik Sipil, 2020
Shear force in general greatly contributes to cause failure of castellated beams so  diagonal stiffeners on the openings are required. Optimization was done by vary dimension of openings and diagonal stiffeners.
Erwin Sanjaya
doaj  

Quantitative Evaluation of Surface Whitening Mitigation via Thermal Annealing in Carbon Fiber/Polyphenylene Sulphide Thermoplastic Composite Laminates

Polymer Composites, EarlyView.
Mitigation of surface whitening in CF/PPS laminates via thermal annealing and quantitative image‐based assessment. ABSTRACT Surface whitening is a manufacturing‐induced surface defect in thermoplastic composites, resulting from non‐uniform shrinkage and near‐surface resin instability during cooling.
JongHun Baek, Hyunseok Choi, Tae‐Yeong So, Chan Joo Lee, Jinsu Gim, Hyun‐Taek Lee, Dongearn Kim   +6 more
wiley   +1 more source

THE FLEXURAL BEHAVIOR OF COMPOSITE HYBRID CASTELLATED I-BEAM

Mağallaẗ Al-kūfaẗ Al-handasiyyaẗ
This study examines the flexural behavior of six hybrid composite castellated beams with varying castellated degrees (25%, 33.8%, and 50%). Hybrid beams are formed by utilizing plates with different strengths in the compression and tension zones.
kawthar hussien, Najla'a H. Al-Shareef
doaj   +1 more source

The moment-gradient factor in lateral– torsional buckling of castellated steel beams under mid-span concentrated load [PDF]

Journal of Engineering Research - Egypt, 2018
increasing the value of ( ) H / ho anddecreasing the value of ( ) w w t / h .On theother hand, the influence of ( ) 4 w h / b hasnoticed effect on the value of bC especiallyin big opening.
Mohamed dabaon, MAHMOUD EL-BOGHDADI, Omnia Kharoop, AZA ELAGAMEY   +3 more
doaj   +1 more source

Sepiolite Nanofibers Decorated With Zn Single Sites: A Sustainable Filler for Mechanically Robust and Self‐Healing Ionomeric Elastomer Composites

Polymer Composites, EarlyView.
Fabrication of XNBR nanocomposites reinforced with Zn single‐site decorated sepiolite nanofibers. The resulting composites exhibit high mechanical strength and self‐healing performance, driven by dynamic interactions between the Zn single sites and the XNBR chains (inset).
Paolo Valagussa, Silvia Mostoni, Marianella Hernandez Santana, Itziar Mas Giner, Michele Mauri, Roberto Simonutti, Sandra Diré, Emanuela Callone, Barbara Di Credico, Roberto Scotti, Massimiliano D'Arienzo   +10 more
wiley   +1 more source

OPTIMIZATION OF SIMPLY SUPPORTED CASTELLATED I-BEAMS LOADED BY A UNIFORMLY DISTRIBUTED LOAD

International Journal for Computational Civil and Structural Engineering, 2019
The paper discusses the problem of optimizing the geometric parameters of simply supported I-beams in order to maximize their load carrying capacity.
Oleg Goryachevskiy
doaj   +1 more source

A Strategic Approach to Improving Interfacial Interactions in TPU/POSS Composites via Ball Milling of POSS

Polymer Engineering &Science, EarlyView.
Ball‐milling promotes uniform POSS dispersion in the TPU matrix, markedly improving the mechanical performance of TPU‐POSS composites. ABSTRACT We synthesized TPU/POSS composites through a two‐step process involving the ball milling of POSS to reduce its particle size, followed by in situ polymerization of TPU to reinforce the material.
Sakrit Hait, Rasoul Rahimzadeh, Ica Manas‐Zloczower   +2 more
wiley   +1 more source