Results 131 to 140 of about 28,676 (311)
Water‐Stable Paper‐Based Laser‐Induced Graphene With Asymmetric Water Adhesion and Wettability
Advanced Materials Interfaces, EarlyView.Paper‐based electronics are attractive for sustainable and disposable devices, but often fail in wet environments. By introducing Parafilm into cellulose paper combined with laser conversion, two graphene surfaces with different water interactions are created.
Lingyin Meng +3 more
wiley +1 more source
Colored nanoparticles for ecological dyeing of cellulosic fibers [PDF]
, 2011 Dyeing cellulosic fibres with reactive dyes wastes great quantities of salt and water. The objective of this work is to dye cellulosic fibers using colored nanoparticles (CNPs) as an alternative to dyeing with reactive dyes.
Gomes, Jaime Rocha +2 more
core
Hydrogel‐Based 3D‐Printable Stretchable Pressure Sensor
Advanced Materials Technologies, EarlyView.We present a carbon‐black‐functionalized double‐network granular hydrogel (DNGH) pressure sensor capable of detecting pressures from 200 Pa, equivalent to a light finger touch, up to 500 kPa. The sensor exhibits signal drifts below 3.5% after 800 cycles and response times around 80 ms. Leveraging this broad sensing range, we 3D print this material into
Tianyu Yuan +4 more
wiley +1 more source
Land Use Implications of Expanding Biofuel Demand [PDF]
The Renewable Fuel Standard mandates in the Energy Independence and Security Act of 2007 will require 36 billion gallons of ethanol to be produced in 2022. The mandates require that 16 of the 36 billion gallons must be produced from cellulosic feedstocks.
Bryant, Henry L. +5 more
core +1 more source
Advanced Materials Technologies, EarlyView.This study presents a new biodegradable coating for titanium implants using a natural antimicrobial peptide, caerin 1.9. Applied via solvent casting, the coating offers sustained antibacterial protection and promotes healing. Tested on 3D‐printed porous titanium scaffolds, it effectively prevented infection—including against resistant bacteria—while ...
Hejie Li +7 more
wiley +1 more source
Advanced Materials Technologies, EarlyView.This study explores how machine learning models, trained on small experimental datasets obtained via Phase Doppler Anemometry (PDA), can accurately predict droplet size (D32) in ultrasonic spray coating (USSC). By capturing the influence of ink complexity (solvent, polymer, nanoparticles), power, and flow rate, the model enables precise droplet control
Pieter Verding +5 more
wiley +1 more source
Experimental TGA device for the determination of cellulose pyrolysis behaviour at elevated pressure [PDF]
, 2012 Forestry lignocellulosic biomass is a major renewable energy sources in the world. Carbon generated by Nature through photosynthesis process, could potentially be considered as a neutral energy carrier in term of the greenhouse gas emissions, if it is ...
Boutahar, Nabila +2 more
core
Smart Closed‐Loop Systems in Personalized Healthcare: Advances and Outlook
Advanced Materials Technologies, EarlyView.A smart closed‐loop e‐textile integrates multimodal sensing, onboard processing, wireless communication, and wearable power to enable real‐time physiological/biochemical monitoring and feedback‐controlled therapy. ABSTRACT Smart textiles represent a revolutionary frontier in healthcare, seamlessly blending fabric and advanced technologies to create ...
Safoora Khosravi +12 more
wiley +1 more source
Adenine as Epoxy Resin Hardener for Sustainable Composites Production with Recycled Carbon Fibers and Cellulosic Fibers. [PDF]
Polymers (Basel), 2020 Merighi S +3 more
europepmc +1 more source
Novel approaches to the construction of miniaturized analytical instrumentation [PDF]
This paper focuses on the design, construction, preliminary testing, and potential applications of three forms of miniaturized analytical instrumentation.
Bastiaans, Glenn J. +8 more
core +1 more source