Results 11 to 20 of about 1,224 (176)
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee +7 more
wiley +1 more source
Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method
Advanced Engineering Materials, EarlyView.A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley +1 more source
Advanced Functional Materials, EarlyView.Monolithic UV‐ozone oxidation of Ta forms an ultrathin Ta2O5/TaOx bilayer enabling resistive switching with a vertical defect gradient. A stoichiometric surface layer over an oxygen‐deficient sublayer promotes localized filament nucleation near the top interface, enabling low‐voltage operation, and reduced cycle‐to‐cycle variability.
Seunghoon Yang +11 more
wiley +1 more source
Advanced Healthcare Materials, EarlyView.We introduce a new fabrication method that overcomes the current limitation of tubular gap electrospinning. We successfully fabricated a seamless hollow tube with fibers aligned along the longitudinal axis in diameters as small as 300 µm, and then reinforced it using 4‐axis 3D printing.
Seyed Aliakbar Hosseini Toopghara +9 more
wiley +1 more source
Advanced Healthcare Materials, EarlyView.A heart‐on‐a‐chip model of dilated cardiomyopathy is developed from patient‐derived induced pluripotent stem cells. The model recapitulates key disease phenotypes and enables functional assessment through integrated bead‐based tracking and pillar deflection measurements.
Ali Mousavi +10 more
wiley +1 more source
Advanced Materials, EarlyView.AI‐Assisted Workflow for (Scanning) Transmission Electron Microscopy: From Data Analysis Automation to Materials Knowledge Unveiling. Abstract (Scanning) transmission electron microscopy ((S)TEM) has significantly advanced materials science but faces challenges in correlating precise atomic structure information with the functional properties of ...
Marc Botifoll +19 more
wiley +1 more source
Advanced Materials, EarlyView.The engineering of colloidal nanocrystals with complex compositions has emerged as a highly active area of research within nanomaterials science. This review covers key aspects of colloidal solid‐solution nanocrystal formation using pulsed laser irradiation.
Marina T. Candela +4 more
wiley +1 more source
Advanced Materials, EarlyView.A photoactive tweezers system based on photoactive colloids is developed and systematically investigated in this study. Through experimental and theoretical methods, we demonstrate that the photoredox reaction catalyzed by a dye‐sensitized TiO2 particle generates a strong positive phototaxis, enabling self‐entrapment in the beam center.
Jingyuan Chen +9 more
wiley +1 more source
Advanced Materials, EarlyView.This work introduces sustainable PLA/graphene oxide bioelectronic interfaces featuring electrodes with tunable conductivity and strong electrocatalytic performance. These platforms were used to implement a new method for tuning astrocyte Ca2+ signaling and for the efficient detection of key biomarkers.
Alessandra Scidà +15 more
wiley +1 more source