Results 61 to 70 of about 522 (180)

Development of an Energy-Efficient Machining Chip Dryer for Enhanced Metal Recycling [PDF]

EPJ Web of Conferences
This study presents the design, analysis, and optimization of a machining chip dryer tailored for industrial environments generating substantial quantities of metal chips during turning, milling, and drilling operations.
Chitte Pritish, Govind Vaishnavi, Yerpul Neha, Sontakke Sakshi, Deshmukh Bhagesh, Pawar Prabhakar   +5 more
doaj   +1 more source

Heat Shielding of Steel With a Polyelectrolyte Coacervate Coating

Macromolecular Materials and Engineering, Volume 311, Issue 7, July 2026.
A polyelectrolyte complex coacervate is reinforced with two types of nanoclay to create a heat shielding layer for steel that is low‐cost and efficient, yet applicable to a variety of civil infrastructure to aircraft components. The incorporation of clay into the coacervate aids in the formation of a reinforced char barrier during degradation ...
Justin D. Alpern, Anastasia B. Contreras, Sarah G. Fisher, Margaret J. Karim, Jaime C. Grunlan   +4 more
wiley   +1 more source

Active vibration control of the flexible high-speed rotor with magnetic bearings via phase compensation to pass critical speed

Journal of Low Frequency Noise, Vibration and Active Control, 2019
In modern industries, high-speed motors and generators have received great attention, and they are widely used in micro turbine, centrifugal compressor, blower, etc.
Shaolin Ran, Yefa Hu, Huachun Wu, Xin Cheng   +3 more
doaj   +1 more source

The characteristic of a centrifugal blower and the flow near the Tongue

Journal of the Visualization Society of Japan, 2000
A study of internal centrifugal blower is very interest in case problems for improve the characteristics. Also, the form of volute tongue which have an affects to characteristics centrifugal blower. This paper is described about effect of tongue shape for characteristics of centrifugal blower.
KOIZUMI, Atsushi, ODAGIRI, Tetsuo, AOKI, Katsumi   +2 more
openaire   +2 more sources

Treatment of Confectionery and Gum Factory Wastewater Effluent

Adsorption Science & Technology, 2000
A pilot plant for the treatment of wastewater was designed, constructed and installed for the continuous treatment of 250 l/d wastewater originating from a gum and confectionery factory.
Guzine El Diwani, Hamman El Abd, Salwa Hawash, Nagwa El Ibiari, Shadia El Rafei   +4 more
doaj   +1 more source

An experimental and numerical investigation on aerodynamic characteristics for different airfoil sections for external flow

Sukkur IBA Journal of Emerging Technologies
This research presents the development of a subsonic wind tunnel designed for streamlined airflow, featuring a squared cross-sectional area along its length.
Irsa TALIB
doaj   +1 more source

Method for Optimization of the Gasifier Recovery Zone Height

Journal of Sustainable Development of Energy, Water and Environment Systems, 2019
The article provides the results of experimental studies of the effect of air introduction into a gasifier, the fuel particle size, and the recovery zone height on a content of carbon monoxide in wood gas.
Gennadii Golub, Saveliy Kukharets, Yaroslav Yarosh, Vyacheslav Chuba   +3 more
doaj   +1 more source

On the enhancement of acceptable blockage of open jet wind tunnel by employing modifications based on concepts of boundary layer and jet flow for testing of aero-rotors

Results in Engineering
The conventional closed and open jet tunnels suffer from various adverse blockage effects that alter the flow conditions generating erroneous results when larger than allowable blockage models are tested. The maximum acceptable blockage is limited to 25 %
Ath S. Singhal, S.V. Jain, R.N. Patel, Vatsal Parmar, Rohan Pathak   +4 more
doaj   +1 more source

Performance of Rotary Cutter Type Breaking Machine for Breakingand Deshelling Cocoa Roasted Beans

Coffee and Cocoa Research Journal, 2005
Conversion of cocoa beans to chocolate product is, therefore, one of the promising alternatives to increase the value added of dried cocoa beans. On the other hand, the development of chocolate industry requires an appropriate technology that is not ...
Sukrisno Widyotomo, Sri Mulato, Edi Suharyanto   +2 more
doaj   +1 more source

Simulation of Impeller Exit Flows of A Centrifugal Blower

International Journal of Recent Technology and Engineering (IJRTE), 2019
The flow through centrifugal impeller is highly non uniform due to formation of regions with different energy level. These region mixes at the exit of the impeller leading to loss and bringing down the efficiency of the centrifugal impeller. The present study focus on analyzing the flow through an impeller and investigating the impeller exit flows. The
Seralathan S*, Balaji R, Mukesh Nadarajan, Ijas Ahamed A, Hariram V   +4 more
openaire   +1 more source