Results 161 to 170 of about 26,146 (270)

Appearance Inspection‐Based Typical Damage Investigation of Concrete Curved Girder‐Type Bridges Subjected to Temperature and Vehicle Effect

Engineering Reports, Volume 8, Issue 5, May 2026.
Technical approach of the article. ABSTRACT This study focuses primarily on concrete curved girder‐type bridges, which are commonly used for urban roads and highways. Over the last two decades, practical experience in bridge engineering has shown that these bridges have unique mechanical and damage characteristics, unlike conventional straight bridges.
Sai Gong, Qiwen Jin, Yili Sun, Tongning Wang, Shixiang Ding   +4 more
wiley   +1 more source

Fatigue safety factor of a transonic centrifugal compressor impeller subject to blade thickness. [PDF]

Sci Rep
Kabalyk K, Bednarz A, Kantyka K.
europepmc   +1 more source

Stability Improvement of High-Pressure-Ratio Turbocharger Centrifugal Compressor by Asymmetric Flow Control-Part I: Non-Axisymmetrical Flow in Centrifugal Compressor. [PDF]

J Turbomach, 2013
Yang M, Zheng X, Zhang Y, Bamba T, Tamaki H, Huenteler J, Li Z.   +6 more
europepmc   +1 more source

Propulsion system study for Small Transport Aircraft Technology (STAT) [PDF]

Propulsion system technologies applicable to the generation of commuter airline aircraft expected to enter service in the 1990's are identified and evaluated in terms of their impact on aircraft operating economics and fuel consumption.
Hirschkron, R., Smith, C. E., Warren, R. E.   +2 more
core   +1 more source

Dewatering combined with Moringa oleifera extract coagulation for industrial‐grade cassava starch concentration

Journal of Chemical Technology &Biotechnology, Volume 101, Issue 5, Page 1094-1102, May 2026.
Abstract Background Efficient dewatering is a critical step in cassava starch production because the moisture content of the concentrated slurry directly affects downstream drying costs and overall process efficiency. Conventional concentration routes, including sedimentation and centrifugation, often provide limited cake dryness and can increase ...
Maria Eduarda S Speretta, Amarilis S Souza, Ana Carolina R Stoppe, Marcelo S Bacelos, Kássia G Santos   +4 more
wiley   +1 more source

Research on multi-condition optimization of centrifugal compressor impeller meridian profile. [PDF]

PLoS One
Yu N, Yu X, Cai Z, Yang X, Tian L, Li S.
europepmc   +1 more source

Dental composites: a comprehensive review on formulation, properties and recent developments

Polymer International, Volume 75, Issue 5, Page 365-386, May 2026.
Dental composites are essential in modern restorative dentistry; this review covers their development, composition, key properties and recent advances, highlighting new technologies for optimizing materials and improving clinical outcomes. Abstract Dental composites have evolved considerably since their introduction, becoming the cornerstone of modern ...
Rayenne Latoui, Djallel Bouzid, Olivier Boyron   +2 more
wiley   +1 more source

Efficacy evaluation of pneumatic solid set canopy delivery system to control powdery mildew (Erysiphe necator) in Washington vineyards

Pest Management Science, Volume 82, Issue 5, Page 4815-4828, May 2026.
The findings of this study indicate that powdery mildew control achieved with the pneumatic solid set canopy delivery system (PSD‐SSCDS) was comparable with that of a conventional airblast sprayer. These results highlight the PSD‐SSCDS as a promising alternative spray technology. Abstract BACKGROUND In this study, a previously optimized pneumatic spray
Dattatray G Bhalekar, Eric Mozzanini, Ramesh K Sahni, Michelle M Moyer, Lav R Khot   +4 more
wiley   +1 more source

Aerodynamic performance enhancement of centrifugal compressor using numerical techniques. [PDF]

F1000Res
S S, A AM, G S.
europepmc   +1 more source

Experimental investigation on centrifugal compressor blade crack classification using the squared envelope spectrum. [PDF]

Sensors (Basel), 2013
Li H, Zhang X, Xu F.
europepmc   +1 more source