Results 111 to 120 of about 309 (125)
Some of the next articles are maybe not open access.
Study on Preparation and Property of Carbon Fiber/HA Composites by Centrifugal Slip Casting Method
Advanced Materials Research, 2014In this paper, centrifugal slip casting method was use to prepare carbon fiber/HA composites using the nanoHA particles and carbon fibers as initial materials. The morphology of the carbon fiber after modification of p-aminobenzoic acid was observed. The rheological characteristic of the carbon fibers/HA slurries was studied.
Jing Yuan Yu, Yu Jing Yuan
exaly +2 more sources
Mechanical Properties of a Graded Alumina-Zirconia Composite Prepared by Centrifugal Slip Casting
AIP Conference Proceedings, 2008Compositionally graded composite of alumina‐20 vol%zirconia was fabricated by using centrifugal casting incorporated with relatively thin slip. An EPMA analysis exhibited a nearly linear variation of the alumina/zirconia ratio along the centrifugal direction; zirconia tended to accumulate in the bottom section, while alumina in the top section.
Motozo Hayakawa +2 more
exaly +2 more sources
Centrifugal slip casting of zirconia (TZP)
Journal of the European Ceramic Society, 1994Abstract Tetragonal zirconia (3Y-TZP) ceramic parts were produced via centrifugal slip casting. This forming method combines the advantages of wet powder preparation with a very efficient densification technology to produce massive and near-net-shape ceramic parts.
W. Huisman, T. Graule, L.J. Gauckler
openaire +1 more source
Preferred orientation of BSCCO via centrifugal slip casting
Journal of Materials Research, 1994Due to the highly anisotropic properties of BSCCO superconductors, the bulk properties of these materials can be greatly affected by preferential orientation. Substantial c-axis orientation normal to the desired direction of current flow has been demonstrated by centrifugally slip casting lead-doped BSCCO-2223.
Greg Steinlage +5 more
openaire +1 more source
Ceramics InternationalNew Al 2 O 3 –Cu–Ni functionally graded composites manufactured using the centrifugal slip casting
International Journal of Applied Ceramic Technology, 2020Abstract The aim of this paper was to establish the general suitability of the centrifugal slip casting technique for fabrication of graded material from the Al 2 O 3 –Cu–Ni system.
Justyna Zygmuntowicz +4 more
openaire +1 more source
Advanced Materials Research, 2012
BP neural network model was developed for prediction of the flexural properties of Al2O3 ceramic prepared by centrifugal slip casting. In this paper, the model can well reflect the relationship between the process parameters including solid content of Al2O3 ceramic slurries (w), centrifugal acceleration (v), sintering temperature (T) and flexural ...
Jing Yuan Yu, Xu Dong Sun, Yu Jing Yuan
exaly +2 more sources
BP neural network model was developed for prediction of the flexural properties of Al2O3 ceramic prepared by centrifugal slip casting. In this paper, the model can well reflect the relationship between the process parameters including solid content of Al2O3 ceramic slurries (w), centrifugal acceleration (v), sintering temperature (T) and flexural ...
Jing Yuan Yu, Xu Dong Sun, Yu Jing Yuan
exaly +2 more sources
Advanced Materials Research, 2012
Mass segregation of Al2O3 slurries during centrifugal slip casing has important effect on microstructure and mechanical property of sintered Al2O3 ceramic, so the study on effect of centrifugal process parameters on mass segregation of slurries has significant meaning.
Jing Yuan Yu, Qiang Li
openaire +1 more source
Mass segregation of Al2O3 slurries during centrifugal slip casing has important effect on microstructure and mechanical property of sintered Al2O3 ceramic, so the study on effect of centrifugal process parameters on mass segregation of slurries has significant meaning.
Jing Yuan Yu, Qiang Li
openaire +1 more source
Materials Science Forum, 2004
Centrifugal casting method was used to fabricate composites with graded structures in alumina-zirconia system. The composition profiles of the graded composites showed three distinct regions, with a greater part of the specimen showing nearly linear variation of compositions.
X.D. Li +4 more
openaire +1 more source
Centrifugal casting method was used to fabricate composites with graded structures in alumina-zirconia system. The composition profiles of the graded composites showed three distinct regions, with a greater part of the specimen showing nearly linear variation of compositions.
X.D. Li +4 more
openaire +1 more source
ATZ Ceramics Prepared by Slip-Casting and Centrifugal Slip-Casting
Key Engineering Materials, 2001Eva Gregorová, Jiří Havrda, W. Pabst
openaire +1 more source