Results 31 to 40 of about 309 (125)

Innovative development and structural behavior of hollow columns using inflatable molds

Structural Concrete, EarlyView.
Abstract This study introduces a novel approach for constructing hollow columns using precast (PC) methods enhanced by inflatable air tubes as internal molds. The proposed method addresses practical challenges in conventional hollow column construction, such as limited constructability, high production cost, and interference between internal molds and ...
Soo Hyung Kim, Dohak Kim, Jeongun Lee, Yun Mook Lim   +3 more
wiley   +1 more source

Multifunctional Crushing and Piezoresistive Self‐Sensing in Conductive Epoxy/CNT‐Coated Polyetherimide TPMS Lattices

Advanced Engineering Materials, Volume 28, Issue 11, 3 June 2026.
This study reports lightweight polyetherimide triply periodic minimal surfaces lattices coated with carbon nanotube‐reinforced epoxy that combine mechanical robustness with self‐sensing. The conformal coating enhances stiffness, strength and energy absorption while enabling reliable strain monitoring.
A. Triay, J. Schneider, P. Harrison, S. Kumar   +3 more
wiley   +1 more source

Terrestrial Analogs to Titan for Geophysical Research

Reviews of Geophysics, Volume 64, Issue 2, June 2026.
Abstract Saturn's moon Titan exhibits remarkable parallels to the Earth in many geophysical and geological processes not found elsewhere in the solar system at the present day. These include a nitrogen atmosphere with a condensible gas—methane—replacing the Earth's water, leading to an active meteorology with rainfall and surface manifestations ...
Conor A. Nixon, Samuel Birch, Audrey Chatain, Charles Cockell, Kendra K. Farnsworth, Peter M. Higgins, Stéphane Le Mouélic, Rosaly M. C. Lopes, Michael J. Malaska, Mohit Melwani Daswani, Kelly E. Miller, Catherine D. Neish, Olaf G. Podlaha, Jani Radebaugh, Lauren R. Schurmeier, Ashley Schoenfeld, Krista M. Soderlund, Anezina Solomonidou, Christophe Sotin, Nicholas A. Teanby, Tetsuya Tokano, Steven D. Vance   +21 more
wiley   +1 more source

Effect of Sintering Aid Composition and Porosity on the Oxyacetylene Torch Response of Silicon Nitride for RF Windows

Journal of the American Ceramic Society, Volume 109, Issue 6, June 2026.
Silicon nitride samples were slip cast using yttrium oxide–aluminum oxide and ytterbium oxide sintering aids to fabricate plates with up to 40% porosity and compare them to a fully dense commercial standard. Silicon nitride plates were tested with an oxyacetylene torch to investigate changes in front and back face temperature, spectral emissivity ...
Matthew A. Thompson, Rodney W. Trice
wiley   +1 more source

Sustainable Catalyst‐Free PLG Networks: Recyclability, Biodegradability, and Functional Performance

Advanced Functional Materials, Volume 36, Issue 40, 18 May 2026.
A catalyst‐additive free covalent adaptable network is developed from star‐shaped poly(lactide‐co‐glycolide) cross‐linked with pyromellitic dianhydride, enabling internal carboxylic acid‐driven transesterification. The resulting biodegradable network exhibits mechanical robustness (Young's modulus ≈1.6 GPa), complete recyclability, rapid biodegradation
Lars Schwarzer, Emilia Fulajtar, Seema Agarwal   +2 more
wiley   +1 more source

Orientation Engineering of MXene Flakes

Advanced Materials, Volume 38, Issue 25, 4 May 2026.
Orientation engineering of MXene flakes refers to the transformation of disordered MXene flakes into ordered architectures with optimized multiphysical transport properties. Focusing on this topic, this review outlines key principles, characterization, fabrication strategies, and advanced applications of oriented MXene structures.
Yizhou Wang, Shuo Li, Tianchao Guo, Dekang Zhu, Ning Chu, Noor Albar, Dana Alsulaiman, Husam N. Alshareef   +7 more
wiley   +1 more source

Miniaturized 3D Magnetic Force Sensor via Laser‐Assisted Folding and Magnetization for Enhanced Robotic Dexterity

Advanced Science, Volume 13, Issue 29, 22 May 2026.
To achieve 3D force sensing in confined spaces such as fingertips, we developed a laser‐assisted folding and magnetization method to fabricate miniature films with precise centripetal magnetization. The resulting compact sensor delivers high force resolution, rapid response, and long‐term stability, significantly enhancing the manipulation capabilities
Yujie Huang, Huangzhe Dai, Chengqian Zhang, Daofan Tang, Xinxin Zhang, Haonan Sun, Annan Ding, Xuebin Ni, Yizhi Zhang, Chengfeng Pan, Peng Zhao   +10 more
wiley   +1 more source

Appearance Inspection‐Based Typical Damage Investigation of Concrete Curved Girder‐Type Bridges Subjected to Temperature and Vehicle Effect

Engineering Reports, Volume 8, Issue 5, May 2026.
Technical approach of the article. ABSTRACT This study focuses primarily on concrete curved girder‐type bridges, which are commonly used for urban roads and highways. Over the last two decades, practical experience in bridge engineering has shown that these bridges have unique mechanical and damage characteristics, unlike conventional straight bridges.
Sai Gong, Qiwen Jin, Yili Sun, Tongning Wang, Shixiang Ding   +4 more
wiley   +1 more source

Ion‑Mediated Structural Engineering of Hydrogel Interfaces for Tunable Mechanical and Analyte Diffusion Properties in Electrochemical Biosensors

Advanced Materials, Volume 38, Issue 19, 1 April 2026.
An ion‐mediated structural engineering strategy enables versatile modulation of PVA–Alginate hydrogel microstructure. We systematically examine how different ion combinations affect hydrogel mechanical properties and analyte diffusivity. Applying this novel strategy to hydrogel as the outer membrane in an electrochemical glucose biosensor allows ...
Dongwook Lee, Soo A Kim, Beom‐Jun Shim, Yurim Lee, Tae Young Kim, Sunghyun Park, Yeontaek Lee, Hyeong Gyu Choi, Kayoung Son, Su Bin Han, Keun‐Young Yook, Seo Jung Kim, Won‐Yong Lee, Jungmok Seo, Jayoung Kim   +14 more
wiley   +1 more source

Deformation Driven Suction Cups: A Mechanics‐Based Approach to Wearable Electronics

Advanced Science, Volume 13, Issue 20, 9 April 2026.
Deformation‐driven suction cups enable robust, reversible adhesion of wearable electronics to human skin spanning wide mechanical compliance, without adhesives or tight straps. By integrating mechanics modeling, experiments, and contact mechanics theory, this work reveals how cup geometry, substrate compliance, and interfacial adhesion govern suction ...
Seola Lee, Andrew Akerson, Roham Pardakhtim, Ehsan Hajiesmaili, Kevin Rhodes, Zidong Li, Andrew Stanley, Amirhossein Amini, Daniele Piazza, Chiara Daraio, Tianshu Liu   +10 more
wiley   +1 more source