Results 131 to 140 of about 473,413 (369)
Potentiality of common clay in ceramic industry
, 1997 An attempt was made to fabricate different ceramic items made of common clays. The fast depletion of higher grade china clays and progressive increase in the cost of fuel necessitated the development of ceramic bodies by incorporating abundantly ...
Baral, S C, Roy, S, Basu, M K
core
Setup‐Optimized Sequencing in Job Shops: Modeling Workstation Productivity and Lateness Behavior
Advanced Engineering Materials, EarlyView.Setup‐optimized sequencing in job‐shop production creates a trade‐off between productivity improvement and schedule reliability. A WIP‐explicit modeling framework links sequencing‐induced productivity gains and lateness dispersion through the production operating curve.
Friederike Stefanowski +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm +3 more
wiley +1 more source
Metal ceramic wear mechanisms [PDF]
, 1990 Sliding wear of metal-on-ceramic, ceramic-on-metal, and ceramic-on-ceramic have been investigated using a tri-pin-on-disc machine. A technique has been developed for thin foil preparation for transmission electron microscopic examination perpendicular ...
Rainforth, William Mark
core
Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger +2 more
wiley +1 more source
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source
Ceramic electrical insulation for electrical coils, transformers, and magnets
, 2023 Rice, John A [Longmont, CO]; Hazelton, Craig S [Lafayette, CO]; Fabian, Paul E [Broomfield, CO]
openalex +1 more source
Indirect selective laser sintering of an apatite-mullite glass-ceramic [PDF]
, 2004 The main objective of this work was to determine the feasibility of using indirect selective laser sintering (SLS) to produce parts for bone replacement applications from glass-ceramic materials.
Goodridge, Ruth Davina
core