Results 301 to 310 of about 827,093 (340)
Multidimensional assessment of sustainability and competitiveness in the ceramic tile and natural stone industries: a cross-country comparative study. [PDF]
Sci RepYarahmadi R, Asadi AA.
europepmc +1 more source
Misfit dislocations at metal-ceramic and ceramic-ceramic interfaces [Slides]
, 2015 openaire +3 more sources
Brazing of ceramic-to-ceramic and ceramic-to-metal joints in air [PDF]
Frontiers of Mechanical Engineering in China, 2010 Reactive air brazing (RAB) is an emerging technology for the production of ceramic-to-ceramic and ceramic-to-metal joints. In this study, RAB was investigated with respect to the potential applications for solid oxide fuel cells (SOFCs) as one example of use. It was found that alumina could be well brazed by RAB with AgCu and AgCuTi brazes.
Nils Kopp +4 more
openaire +1 more source
Some of the next articles are maybe not open access.
Related searches:
Related searches:
Evaluation of the ceramic/ceramic interface
American Journal of Orthodontics and Dentofacial Orthopedics, 1994The purpose of this study was to investigate bond strength for ceramic orthodontic brackets bonded to dental porcelain. The following factors were tested. Two types of ceramic brackets were placed on two different types of porcelain surfaces with two different bonding systems.
Lambros Zelos +2 more
openaire +3 more sources
Wetting of ceramic-metal and ceramic-ceramic interfaces
[Proceedings] 1990 IEEE 7th International Symposium on Applications of Ferroelectrics, 2002Contact angles of the metal-ceramic interface in a heating process were measured until the metal melted. Ag on BaTiO/sub 3/ disks melted with an almost hemispherical shape at an obtuse angle and did not wet to BaTiO/sub 3/. Metal Ag on superconducting Ba/sub 2/Y/sub 1/Cu/sub 3/O/sub 7- delta / showed better wetting than in the case of BaTiO/sub 3 ...
S. Sugihara, K. Okazaki
openaire +2 more sources
Ceramics and ceramic coatings in orthopaedics
Journal of the European Ceramic Society, 2015no ...
Mcentire, Bj +4 more
openaire +3 more sources
Hydroxyapatite Ceramic Hip Survey: Ceramic/Ceramic Bearings
Key Engineering Materials, 2007This paper describes the clinical application of alumina ceramic and, more recently, Zirconia Toughened Alumina (ZTA), to the bearing surfaces of hip implants with a maximum follow up of fifteen years. Patients are assessed pre- and post-operatively using the Harris Hip Score.
Sally Goodfellow, James M. Buchanan
openaire +2 more sources
2018
Alumina ceramic is a highly oxidized ceramic that is formed by the fusion of microscopic grains of alumina (Al2O3) and/or zirconia (ZrO2) ceramic powder into a solid phase. During the process of sintering known as “hot isostatic pressing,” the agents are pressed above 1000 bars and sintered at 1600 °C [1].
Eustathios Kenanidis +2 more
openaire +2 more sources
Alumina ceramic is a highly oxidized ceramic that is formed by the fusion of microscopic grains of alumina (Al2O3) and/or zirconia (ZrO2) ceramic powder into a solid phase. During the process of sintering known as “hot isostatic pressing,” the agents are pressed above 1000 bars and sintered at 1600 °C [1].
Eustathios Kenanidis +2 more
openaire +2 more sources
Ceramic-on-Ceramic Total Hip Arthroplasty
The Journal of Arthroplasty, 2009Ceramic bearing surfaces have been introduced to prevent bone loss after osteolysis seen with conventional polyethylene bearing surfaces. One hundred three ceramic-on-ceramic total hip arthroplasties in 97 patients were retrospectively reviewed. Average follow-up was 50.4 months.
Frank R. Kolisek +4 more
openaire +3 more sources