Results 31 to 40 of about 33,928 (309)
Advanced Engineering Materials, EarlyView.This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera +8 more
wiley +1 more source
Computer model to predict electron beam-physical vapour deposition (EB-PVD) and thermal barrier coating (TBC) deposition on substrates with complex geometry [PDF]
, 2000 For many decades gas turbine engineers have investigated methods to improve engine efficiency further. These methods include advances in the composition and processing of materials, intricate cooling techniques, and the use of protective coatings ...
Pereira, Vitor Emanuel M. Loureiro S.
core
, 2010 Plasma electrolytic oxidation, or PEO, is a surface modification process for the production of ceramic oxide coatings upon substrates of metals such as aluminium, magnesium and titanium.
core +1 more source
Advanced Engineering Materials, EarlyView.Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley +1 more source
Design of experiment analysis of high velocity oxy-fuel coating of hydroxyapatite [PDF]
, 2009 Due to the flexibility and cost effectiveness the high velocity oxy-fuel (HVOF) thermal spray process has been widely adopted by many industries. Though there are different types of flame spraying processes, the HVOF thermal spray process utilises only ...
Hasan, Shahriar
core
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study explored how effective nickel aluminide coatings are obtained in providing oxidation resistance applied to the Inconel 738 alloy, modeling with diffusion models. In the present study, kinetics and thermal behavior of the Inconel 738 alloy were studied by the low‐temperature thermoreactive aluminizing process, which was carried out at 625°C ...
Gozde Celebi Efe +4 more
wiley +1 more source
Processing and characterization of monoclinic-zirconia fibre-matrix interfaces in dense matrix alumina-alumina composites: Processamento e caracterização de interfaces fibra-matriz de zircônia não estabilizada em compósitos alumina-alumina de matriz densa [PDF]
, 2013 Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro Tecnológico, Programa de Pós-Graduação em Engenharia Mecânica, Florianópolis, 2013.Interfaces fibra-matriz tem um papel muito importante no desempenho de compósitos de matriz ...
Blaese, Diego
core
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Investigation into laser re-melting of inconel 625 HVOF coating blended with WC [PDF]
, 2009 High velocity oxy-fuel (HVOF) spraying of Diamalloy 1005 powders mixed with WC particles onto steel (304) is considered and laser re-melting of the resulting coatings is examined.
Al-Taha, Zuhair Y.
core