Results 71 to 80 of about 963,442 (192)

Optimisation of material composition in functionally graded plates for thermal stress relaxation using statistical design support system

open access: yesCurved and Layered Structures
This study addresses the optimisation of material composition in a functionally graded plate for thermal stress relaxation, subjected to through-thickness thermal gradients, with the aim of minimising a stress utilisation ratio.
Chiba Ryoichi, Sugano Yoshihiro
doaj   +1 more source

Influence of the geometry of ceramic specimens on biaxial flexural strength: experimental testing and finite element analysis

open access: yesCerâmica
This study evaluated the influence of the geometry of ceramic specimens (disc vs. square plate) on the biaxial flexural strength (BFS) using an experimental set and finite element analysis (FEA).
J. da S. Ramos   +3 more
doaj   +1 more source

West Pans Pottery Ceramic Resource Disk 2

open access: yes, 2006
The West Pans ceramic material, listed described and photographed on the enclosed disk has been assigned to the National Museums of Scotland and was catalogued using accession numbers (MES1.1 to 1132).
Haggarty, George
core  

Plate dynamics, mantle structure and tectonic evolution of the Caribbean region [PDF]

open access: yes, 2013
The northeastern Caribbean exhibits high deformation and is fragmented by several faults into smaller tectonic blocks. One of these faults was the site of the catastrophic 12th of January 2010 earthquake. In this thesis I aim to constrain the main forces
How plate tearing and slabs drive reorganization of the N Caribbean plate boundary   +2 more
core  

Effects of hardness and toughness of ceramic in a ceramic armour module against long rod impacts

open access: yes, 2019
A series of experiments and simulations were conducted to investigate the effects of hardness and toughness of ceramic on the ballistic performance of ceramic armour modules.
Zeng, Zhiping   +4 more
core   +1 more source

Large Section Ceramic Injection Moulding [PDF]

open access: yes, 2000
PhDCeramic injection moulding is already established as a production technique for complex shaped ceramic components. However the process is limited to thin section mouldings generally not exceeding a wall thickness of 10 mm.
Krug, Steffen
core   +1 more source

Transversal bleustein-gulayev (B.G.) surface waves on a piezoelectric ceramic

open access: yesArchives of Acoustics, 2016
In this paper the results of investigations of piezoelectric ceramic of the type lead zirconate-titanate (PZT) used as a basis for acoustic-electric waves (B.G.) are presented.
Wincenty PAJEWSKI
doaj  

Microstructure and mechanical properties of AlN/Cu joints brazed by Ag-Cu-Ti + Y2O3 composite brazing alloy

open access: yesHanjie xuebao
Copper-clad ceramic plate is an important heat dissipation component in an insulate-gate bipolar transistor (IGBT), which is composed of high thermal conductivity ceramic and pure copper connection.
Yanming HE   +6 more
doaj   +1 more source

MENGATASI HOT SPOTS WALL RADIANT CABIN PLATE DENGAN METODE PELAPISAN MATERIALS HEAT INSULATION

open access: yesJournal of Industrial Engineering and Operation Management
Permasalahan yang dihadapi adalah terjadinya hot spot pada wall radiant reformer furnace unit hidrogen proses yang berdampak pada kondisi sub standard dan unsafe condition peralatan proses unit.
Sulardi Sulardi
doaj   +1 more source

Drying of a Clayey Ceramic Flat Plate: Simulation Studies Using the Galerkin-Based Integral Method

open access: yesBuildings
The ceramics sector is crucial to the global economy. This research is devoted to studying the drying process of ceramic parts with arbitrary shapes based on Fick’s second law of diffusion and energy conservation.
Ivonete B. Santos   +10 more
doaj   +1 more source

Home - About - Disclaimer - Privacy