Results 41 to 50 of about 1,091 (180)

Stochastic Computer Simulation of Cermet Coatings Formation

Advances in Materials Science and Engineering, 2015
An approach to the modeling of the process of the formation of thermal coatings lamellar structure, including plasma coatings, at the spraying of cermet powders is proposed. The approach based on the theoretical fundamentals developed which could be used
Oleg P. Solonenko, Vladimir I. Jordan, Vitaly A. Blednov   +2 more
doaj   +1 more source

Cermets and Hardmetals [PDF]

Metals, 2018
Cermets and hardmetals combine the most favorable characteristics of ceramics and metals, namely the high hardness and elastic moduli of the former, and the ductility and toughness of the latter. [...]
openaire   +2 more sources

Corrosion and Process Analysis of a Preoxidized MgO Recyclate‐Based Cermet Anode in Laboratory‐Scale Na‐Cryolite Molten Salt Electrolysis of Aluminum at 1000°C

Advanced Engineering Materials, Volume 28, Issue 10, 20 May 2026.
EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk, Farhan Hossain, Felipe A. Garcia Paz, Serhii Yaroshevskyi, Felix Drechsler, Daniel Vogt, Christos G. Aneziris, Alexandros Charitos   +7 more
wiley   +1 more source

High-speed cutting performance characteristics of Ti(C, N)–W cermet tools against S32750 super-duplex stainless steel round bars

Journal of Materials Research and Technology
In this study, TiC0.5N0.5–60 wt% W and TiC0.5N0.5–70 wt% W cermet cutting tool specimens consisting of Ti(C, N) core, W-rich Ti(C, N) rim, and W-based alloy phases with much higher strengths than conventional heat-resistant tool materials at temperatures
Takashi Murakami, Jonny Herwan, Ichiro Ogura, Atsushi Korenaga   +3 more
doaj   +1 more source

Raman Spectroscopic Identification of Oxide Phases in a Corroded MgO–Steel Composite Anode Used in Aluminum Molten Salt Electrolysis

Advanced Engineering Materials, Volume 28, Issue 10, 20 May 2026.
Micro‐Raman spectroscopy is applied to characterize corrosion products in a recycled‐based MgO–316L steel composite anode after molten salt electrolysis. A depth‐dependent Fe–O/Fe–Al–O layer sequence of magnetite, hercynite, and an Al‐doped magnetite transition zone is identified.
Felix Drechsler, Serhii Yaroshevskyi, Alexander Adamczyk, Mahnaz Mehdizadehlima, Julia Richter, Cameliu Himcinschi, David Rafaja, Alexandros Charitos, Christos G. Aneziris, Jens Kortus   +9 more
wiley   +1 more source

Interaction of MgO Recyclate‐Based Cermet Anode With KF‐AlF3‐Al2O3 at 800°C During Laboratory Scale Aluminum Molten Salt Electrolysis

Advanced Engineering Materials, Volume 28, Issue 10, 20 May 2026.
A carbon‐free, as‐sintered MgO–steel cermet anode, fabricated via cold isostatic pressing using MgO–C refractory recyclate, was evaluated under laboratory‐scale K‐cryolite electrolysis at 800°C. Operation at this reduced temperature, combined with the electrolyte's limited electrical conductivity, led to an increase in cell voltage.
Farhan Hossain, Alexander Adamczyk, Felipe Alejandro Garcia Paz, Serhii Yaroshevskyi, Felix Drechsler, Daniel Vogt, Christos G. Aneziris, Alexandros Charitos   +7 more
wiley   +1 more source

Toward Low‐Consumable Anodes: Process Simulation and Prospective Life Cycle Assessment of NiFe2O4‐NiO‐Ni‐Cu vs. Prebaked Anodes for Aluminum Production with use of Molten Salt Electrolysis

Advanced Engineering Materials, Volume 28, Issue 10, 20 May 2026.
Low‐consumable nickel ferrite‐based anodes for the Hall–Héroult process are compared with conventional prebaked carbon anodes using thermodynamic simulation and prospective life cycle assessment under contrasting future electricity system pathways from 2025 to 2050.
Felipe Alejandro Garcia Paz, Ulziikhuu Otgonbayar, Alexander Adamczyk, Farhan Hossain, Daniel Vogt, Johan Berg Pettersen, Alexandros Charitos   +6 more
wiley   +1 more source

Impact of Pre‐Oxidation Treatments on a Recycled MgO/Steel‐Composite as Carbon Free Anode in Aluminum‐Electrolysis Environments

Advanced Engineering Materials, Volume 28, Issue 10, 20 May 2026.
Cermets (60 vol.% AISI 316L stainless steel, 40 vol.% recycled MgO), intended for use in aluminum electrolysis, were pre‐oxidized in three furnaces with different heating technologies and subjected to a cryolite corrosion test. The different atmospheres influenced the formation of oxide layers, which in turn affected corrosion resistance and ...
Patricia Kaiser, Felix Drechsler, Nora Brachhold, Florian Kerber, Christos G. Aneziris   +4 more
wiley   +1 more source

Estudio por emisión acústica del comportamiento a flexión de recubrimientos WC-Co obtenidos por plasma atmosférico

Revista de Metalurgia, 2007
Los recubrimientos de cermet WC-Co proyectados por plasma se utilizan en un amplio rango de aplicaciones industriales, principalmente por su resistencia al desgaste, incluso en medio corrosivo.
F. Segovia, E. Klyatskina, V. Bonache, M. D. Salvador, E. Sanchez, V. Cantavella, C. Bloem   +6 more
doaj   +1 more source

Production of MgO/TiC Composites From MgO‐C Recyclates Using Spark Plasma Sintering

Advanced Engineering Materials, Volume 28, Issue 10, 20 May 2026.
Using the spark plasma sintering technique, MgO/TiC composites are manufactured from recycled MgO‐C refractories stemming from the steel production that were mixed with titanium powder. This article shows, how the size of the Ti grains and their distribution in the powder mixture affect the local carbon concentration in TiC.
Jiayan Yu, Christian Schimpf, Stefan Martin, David Rafaja   +3 more
wiley   +1 more source