Results 91 to 100 of about 7,005 (204)

Infrared Thermographic Assessment of Fatigue Behavior in Bolted Composite Joints

Fatigue &Fracture of Engineering Materials &Structures, EarlyView.
ABSTRACT This study investigates the temperature evolution of bolted thick glass fiber reinforced polymer composites during fatigue testing. Three different adherend thicknesses (8, 10, and 12 mm) and three different bolt tightening torques (30, 40, and 50 N·$$ \cdotp $$m were considered to evaluate the effects of adherend thickness and bolt tightening
Tolga Topkaya, Hüsna Topkaya, Murat Yavuz Solmaz   +2 more
wiley   +1 more source

Structural characterization and optimum machining parameters of jute/carbon fibre hybrid reinforced epoxy composite laminates

Polymer International, Volume 75, Issue 9, Page 804-817, September 2026.
Hybrid jute/carbon epoxy laminates have better mechanical performance and less drilling damage by the use of optimized stacking sequence and machining parameters. Abstract Three composite laminate systems were produced using the standard hand lay‐up method: jute‐fibre‐reinforced polymer (JFRP), carbon‐fibre‐reinforced polymer (CFRP) and a hybrid of the
Paulraj Prabhu, Anbalagan Arunkumar, Nadir Ayrilmis, Vellingiri Suresh, Ram Subbiah, Emarose Shankar   +5 more
wiley   +1 more source

Thermoplastic‐Resin Transfer Molding Technology: Development and Challenges Toward Industrialization

Polymer Composites, Volume 47, Issue 15, Page 13317-13358, 10 August 2026.
Illustration of the key aspects involved in the manufacture of thermoplastic composites by T‐RTM highlighting the relationships between raw materials, resin mixing strategies, polymerization parameters, and processing equipment ranging from laboratory to industrial scale. ABSTRACT Driven by increasingly stringent international environmental regulations,
Filipe P. Martins, Paulo S. Lima, Ricardo Torcato, Laura Santos, J. M. Oliveira   +4 more
wiley   +1 more source

Manufacturability‐Aware Multi‐Objective Screening of Filament‐Wound Type IV Pressure‐Vessel Cylindrical Sections Using Dual‐Pressure Hashin Constraints

Polymer Composites, Volume 47, Issue 15, Page 13854-13875, 10 August 2026.
Manufacturability‐aware multi‐objective screening of Type IV filament‐wound composite pressure‐vessel cylindrical sections toward lightweight and high‐strength designs. ABSTRACT A manufacturability‐aware preliminary screening framework is proposed for the straight cylindrical section of filament‐wound Type IV composite pressure vessels.
Önder Albayrak, Ahmet Çalık
wiley   +1 more source

The Influence of Number of CFRP Layers on the CFRP Concrete Bond Behavior [PDF]

Sixth International Conference on Advances in Civil Structural and Mechanical Engineering CSM 2018, 2018
AMMAR I, WASIM S., YASMEEN T
openaire   +1 more source

Vergleichende Untersuchung der Eigenschaften recycelter Kohlenstofffasern Comparative investigation of the properties of recycled carbon fibers

Chemie Ingenieur Technik, Volume 98, Issue 8, Page 485-494, August 2026.
Die Akzeptanz recycelter Kohlenstofffasern in der Industrie erfordert eine hohe und standardisierte Faserqualität. In diesem Artikel werden mechanische Eigenschaften sowie die Oberflächenqualität neuer und recycelter Kohlenstofffasern ermittelt und verglichen, um Optimierungspotentiale für das CFK‐Recycling abzuleiten.
Philipp Karsten Niebel, Violetta Schumm, Mareen Zöllner, Thomas Krampitz, Holger Lieberwith, Marcel Zeisberg, Enrico Baumgärtel, Jens Bachmann   +7 more
wiley   +1 more source

Behavior of a Novel Cyclic Olefin‐Based Hot‐Melt Adhesive in CFRP Adhesive Joints Compared to Conventional Epoxy‐Based Structural Adhesives

Polymer Composites, Volume 47, Issue 13, Page 11783-11797, 10 July 2026.
Rate‐dependent performance of composite adhesive joints using thermoset and thermoplastic adhesives, in terms of toughness and fatigue behaviour. ABSTRACT A recently developed hot‐melt adhesive (HMA) based on cyclic olefin chemistry, supplied as a transparent, non‐tacky thermoplastic film with a distinctive polymer microstructure, was evaluated in this
Hossein Malekinejad, Ricardo J. C. Carbas, Eduardo A. S. Marques, Lucas F. M. da Silva   +3 more
wiley   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, Volume 28, Issue 13, 8 July 2026.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

SEISMIC PERFORMANCE OF RC BUILDING COLUMNS CONFINED WITH CFRP

Facta Universitatis. Series: Architecture and Civil Engineering
It is a usual practice that traditional methods with traditional materials (most frequently jacketing of elements) are used for repair and strengthening of structures.
Artur Roshi, Golubka Nechevska-Cvetanovska, Julijana Bojadjieva, Jordan Bojadjiev   +3 more
doaj   +1 more source

Experimental study on mechanical properties and failure behavior analysis of CFRP riveted joints with gaskets and bushings

Xibei Gongye Daxue Xuebao
The application of gaskets, bushings or their combination can significantly improve the joining strength of composite structures, but there is still a lack of systematic researches on their combined or individual applications. To solve this problem, this
YAN Lu, ZHANG Shang′an, CAO Zengqiang, YAN Han, LU Minxi, HUO Lubin   +5 more
doaj   +1 more source