Results 151 to 160 of about 2,297,875 (300)

Investigating the Low‐Temperature Phase Stability of the Binary Ta–W System

Advanced Engineering Materials, EarlyView.
Atomistic simulations show that the binary Ta–W system forms ordered intermetallic phases, B2‐TaW and D03‐TaW3, as 0 K ground states. Configurational entropy, however, lowers the free energy of the disordered bcc solid solution, which becomes the stable phase above about 400 K.
Klemens Lechner, Anna Sophie Jelinek, Velislava Terziyska, Peter Wagatha, Wolfram Knabl, Christian Mitterer, Helmut Clemens, David Holec   +7 more
wiley   +1 more source

Effects of Mg on Microstructure and Solidification of a Hypereutectic Zn–8 wt.%Al Alloy

Advanced Engineering Materials, EarlyView.
An appreciable set of results involving thermal data, microstructure, chemical composition, and microstructural growth laws is reported for ZnAlMg alloys. Such results demonstrate that ZnAlMg alloys have high potential for applications in automotive self‐lubricating components, batteries, and electrical systems.
Raí B. de Sousa, Jeverton L. Paixão, Daylla S. Silva, Bruno S. Sobral, Mucio D. de Medeiros, José E. Spinelli, Bismarck L. Silva   +6 more
wiley   +1 more source

Cryogenic Deformation Behavior of TiAl and Insights Into Embrittlement After High‐Temperature Exposure Combined With Secondary Ion Mass Spectroscopy of Near Surface Chemistry

Advanced Engineering Materials, EarlyView.
Near‐surface deuterium enrichment profiles for different microstructural types of TiAl after exposure at 700 °C in a heavy water‐containing environment. The deuterium levels are significantly higher than expected from natural occurrence, indicating that the heavy water dissociated during the exposure treatment and entered the specimens.
Jonathan D. H. Paul, Alexander Welle, Dirk Matthiessen, Michael Oehring, Fritz Appel, Florian Pyczak   +5 more
wiley   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Chronic obstructive pulmonary disease: update of today's knowledge and challenges. [PDF]

Ups J Med Sci
Blomberg A.
europepmc   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

A Global Initiative for Chronic Obstructive Lung Disease (GOLD) Science Committee perspective on exacerbations and cardiovascular risk in chronic obstructive pulmonary disease. [PDF]

Am J Respir Crit Care Med
Singh D, Agustí A, Bourbeau J, Martinez FJ, Halpin DMG, Vogelmeier CF.   +5 more
europepmc   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

Advanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar, Shobhit Pratap Singh, Gaurav Mohanty, Praveen Kumar   +3 more
wiley   +1 more source

Microstructural Evolution and In Situ Formation of TiB and TiC in Ti─5Al─2.5Sn Alloy Processed by Powder Metallurgy

Advanced Engineering Materials, EarlyView.
Accelerated in situ formation of TiB and TiC in Ti–5Al–2.5Sn–B4C is driven by transient liquid phase formation, which enhances particle reactions and microstructural evolution. This process increases hardness and establishes a coupled relationship between sintering temperature and reinforcement content, strongly influencing porosity in the resulting ...
Fernando. Y. Kojima, Juliano. Soyama
wiley   +1 more source

Effective Connectivity and Clinical Correlates in Chronic Obstructive Pulmonary Disease. [PDF]

Int J Chron Obstruct Pulmon Dis
Han KI, Bae JH, Jo HJ, Park JM, Yeo Y, Park TS, Park DW, Kim TH.   +7 more
europepmc   +1 more source