Results 121 to 130 of about 79,872,456 (309)
Gap‐Filling Stencil Lithography for Precise and High Yield Patterning of Two‐Dimensional Materials
Advanced Materials Interfaces, EarlyView.Gap‐filling lithography (GSL) for simple and precise patterning for two‐dimensional materials (2DMs) is reported. A 100% pattern yield was successfully achieved across large‐area pattern arrays by introducing a PMMA gap‐filling layer. This GSL efficiently overcomes issues that arise when applying conventional lithography to 2DM. This unique lithography
Jaemin Myoung +18 more
wiley +1 more source
Loosening phenomenon on thin plates bolted joint due to offset load
Journal of Advanced Joining ProcessesIn this study, the new loosening behavior was discovered and investigated when offset loads were repeatedly applied to both ends of a bolted joint initially tightened to a thin plate made of high-tensile steel.
Naoki Yamamoto +2 more
doaj +1 more source
3D Printed Photon Shield Assembly for Low‐Noise Visual Stimulation During Two‐Photon Imaging in Mice
Advanced Materials Technologies, EarlyView.We present the Photon Shield, an open‐hardware system for low‐noise two‐photon calcium imaging during visual stimulation in mice. Combining a 3D‐printed headplate and rail‐mounted shield substantially reduces stray‐light contamination, as quantitatively verified. Functional validation confirms reliable cortical responses. Open design files enable broad
Gergely Katona +6 more
wiley +1 more source
Off-Clamp versus On-Clamp Robotic Partial Nephrectomy: A Multicenter Match-Paired Case-Control Study
, 2017 International audienceINTRODUCTION:The aim of this study was to compare the outcomes of on-clamp and off-clamp robotic partial nephrectomy (RPN).MATERIALS AND METHODS:The charts of all patients who underwent an RPN at 8 institutions between 2010 and 2014
Bensalah, Karim +35 more
core +1 more source
Advanced Materials Technologies, EarlyView.Multilayer aerosol jet printed components with a low‐loss, thermally stable dielectric are demonstrated using benzocyclobutene. Ink formulation and in‐line droplet evaporation control support high‐quality, versatile, and stable printing performance. A specialized measurement for low‐loss materials reveals promising microwave properties, which, combined
Md Ramjan Ali +3 more
wiley +1 more source
Advanced Materials Technologies, EarlyView.Desktop vacuum thermoforming enables rapid, low‐cost fabrication of 96‐channel polystyrene culture chips with very thin imaging interfaces. The resulting platform supports cell lines, primary cells, and patient‐derived organoids, and enables high‐resolution confocal microscopy and single‐cell visualization, providing an accessible approach for advanced
Aleksandra Fomina +5 more
wiley +1 more source
Validation of finite-element model of clamp of rail fastening system
Вестник Научно-исследовательского института железнодорожного транспортаIntroduction. This paper discusses the validation and verif ication process of the finite element model (FEM) of the elastic clamp of the rail fastening system.
V. O. Berezin +3 more
doaj
Characterized Ecoflex Polydimethylsiloxane (PDMS) Hybrids for Advanced Flexible Devices
Advanced Materials Technologies, EarlyView.Ecoflex–PDMS hybrids are systematically characterized to identify an optimal composition that balances stretchability, optical transparency, and plasma bonding, enabling multifunctional applications in stretchable microfluidics, flexible sensing, and soft robotics.
Xiaoyue Kang +10 more
wiley +1 more source
Jixie qiangdu, 2017 The looseness or fall off of the clamp is one of the important factors for the failure of spacer bar. The research on the clamp strength is very important. Based on ANSYS finite element analysis software,non-linear emulation analysis is carried out.
LV ZhongBin +4 more
doaj