Results 1 to 10 of about 1,850,889 (292)
Simultaneous Clamping and Cutting Force Measurements with Built-In Sensors
Sensors, 2020 The intensity of the clamping force during milling operations is very important, because an excessive clamping force can distort the workpiece, while inadequate clamping causes slippage of the workpiece.
Sina Rezvani +3 more
doaj +4 more sources
Optimization Method of the Clamping Force for Large Cabin Parts
Applied Sciences, 2023 In order to realize the stable clamping of large cabin parts, this paper studied the clamping force optimization of the clamping mechanism for large-mass and large-size cabin parts. Firstly, three kinds of contact models are introduced.
Shuangji Yao +3 more
doaj +2 more sources
Clamping force prediction based on deep spatio-temporal network for machining process of deformable parts [PDF]
Scientific Reports, 2023 As an important component of the machining system, the influence of fixtures on the machining deformation of the workpiece cannot be ignored. By controlling the clamping force during the machining process is an effective means to suppress or improve the ...
Enming Li +4 more
doaj +2 more sources
The Effect of Clamping Force on the Wear Behavior of a Steam Generator Tube
Applied Sciences, 2022 Anti-vibration bars (AVBs) are essential components of a steam generator (SG) and are used to prevent steam generator tubes (SGTs) from vibrating intensely because of flow-induced vibration.
Xuxin Dong +6 more
doaj +2 more sources
Protein folding in a force clamp [PDF]
The Journal of Chemical Physics, 2006 Kinetics of folding of a protein held in a force clamp are compared to an unconstrained folding. The comparison is made within a simple topology-based dynamical model of ubiquitin. We demonstrate that the experimentally observed variations in the end-to-end distance reflect microscopic events during folding. However, the folding scenarios in and out of
Cieplak, Marek, Szymczak, Piotr
openaire +3 more sources
The Effect of Clamping Force and Friction Coefficient on The Clamping Clamp
Academic Journal of Science and Technology, 2023 In order to study the influence of clamping force and friction coefficient on the stress distribution of drill pipe joint during the buckling process, the nonlinear contact problem and elastoplastic mechanical properties of Φ139.7mm × 9.17mm drill pipe were simulated by finite element analysis method in this paper, and the stress distribution and size
Jinfeng Li, Jianbing Zhang, Qingtao Meng
openaire +1 more source
Design and Test of a Force Feedback Seedling Pick-Up Gripper for an Automatic Transplanter
Agriculture, 2022 Aiming at the problems of seedling injury and planting leakage due to the lack of seeding clamping force detection and real-time control in vegetable transplanting, a force feedback gripper was developed based on the linear Hall element.
Pengfei Li +4 more
doaj +1 more source
IEEE Access, 2023 After a bolt assembling process, non-destructive identification of the clamping force is important to minimize unexpected failure of the assembled joint structures.
Wanseung Kim +3 more
doaj +1 more source
Piezoresistive cantilever force-clamp system [PDF]
Review of Scientific Instruments, 2011 We present a microelectromechanical device-based tool, namely, a force-clamp system that sets or “clamps” the scaled force and can apply designed loading profiles (e.g., constant, sinusoidal) of a desired magnitude. The system implements a piezoresistive cantilever as a force sensor and the built-in capacitive sensor of a piezoelectric actuator as a ...
Sung-Jin, Park +3 more
openaire +2 more sources
Clamping force of a multilayered cylindrical clamper with internal friction
Theoretical and Applied Mechanics Letters, 2022 Holding an object by clamping force is a fundamental phenomena, layered or laminated architectures with internal sliding features are essential mechanism in natural and man-made structural system. In this paper, we combine the layered architecture and clamping mechanism to form a multilayered clamp and study the clamping force with internal friction ...
Bohua Sun, Xiao-Lin Guo
openaire +1 more source