Results 71 to 80 of about 276,191 (223)

Studying the Synthesis of Graphene Oxide in Ammonium Carbonate Solution [PDF]

open access: yesNanochemistry Research
Studies on the synthesis of graphene oxide in ammonium carbonate solution by electrochemical method were conducted. During the synthesis of graphene oxide, a partial reduction of graphene oxide was observed as a result of stirring the solution.
Khushnudbek Eshchanov   +2 more
doaj   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

open access: yesAdvanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi   +3 more
wiley   +1 more source

On the Clean Graph of Commutative Artinian Rings

open access: yesInternational Journal of Mathematics and Mathematical Sciences
For a commutative Artinian ring R with unity, the clean graph ClR is a graph with vertices in the form of an ordered pair e,u, where e is an idempotent and u is a unit of ring R, respectively.
R. Singh, M. Habibi, S. C. Patekar
doaj   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

open access: yesAdvanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin   +2 more
wiley   +1 more source

A Workflow to Accelerate Microstructure‐Sensitive Fatigue Life Predictions

open access: yesAdvanced Engineering Materials, EarlyView.
This study introduces a workflow to accelerate predictions of microstructure‐sensitive fatigue life. Results from frameworks with varying levels of simplification are benchmarked against published reference results. The analysis reveals a trade‐off between accuracy and model complexity, offering researchers a practical guide for selecting the optimal ...
Luca Loiodice   +2 more
wiley   +1 more source

ALMOST right (left) SEMICLEAN RINGS of SKEW GENERALIZED POWER SERIES

open access: yesJournal of Scientific Research in Science
We extend the notions of almost clean, n-almost clean, and almost semiclean to the non-commutative setting. Then, we demonstrate that under specific conditions that the skew generalized power series rings S[[T,w]] is almost right (left) semiclean if ...
Dina Abdelhakim   +2 more
doaj   +1 more source

Packaging of Macroscopic Material Payloads: Needs, Challenges, Concepts, and Future Directions

open access: yesAdvanced Engineering Materials, EarlyView.
This review introduces a unified framework that decomposes any macroscopic packaging system into the payload, packaging material, and packaging strategy and combines them into a conceptual packaging equation: packaging strategy = payload + packaging material.
Venkata S. R. Jampani, Manos Anyfantakis
wiley   +1 more source

Super strongly clean group rings

open access: yesDiscussiones Mathematicae - General Algebra and Applications, 2023
Amit B. Singh, Susheel Kumar
doaj   +1 more source

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

open access: yesAdvanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé   +5 more
wiley   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

open access: yesAdvanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti   +11 more
wiley   +1 more source

Home - About - Disclaimer - Privacy