Results 31 to 40 of about 1,623 (247)
FEBS Open Bio, EarlyView.Time‐restricted feeding (TRF) in mice increased liver fatty acid oxidation and decreased fatty acid biosynthesis. These alterations persisted when TRF was discontinued and the host was infected with Mycobacterium tuberculosis. Pre‐exposure to TRF did not alter tissue (lung and spleen) mycobacterial burden but significantly reduced CD3+ T cells in lungs
Ashish Gupta +7 more
wiley +1 more source
What Do Large Language Models Know About Materials?
Advanced Engineering Materials, EarlyView.If large language models (LLMs) are to be used inside the material discovery and engineering process, they must be benchmarked for the accurateness of intrinsic material knowledge. The current work introduces 1) a reasoning process through the processing–structure–property–performance chain and 2) a tool for benchmarking knowledge of LLMs concerning ...
Adrian Ehrenhofer +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates how optimizing laser power, scanning speed, and hatching distance in laser powder bed fusion can boost the productivity of Inconel 718 manufacturing by up to 29% while maintaining mechanical integrity. The work delivers a validated process window and cost–time analysis, offering industry‐ready guidelines for efficient additive ...
Amir Behjat +7 more
wiley +1 more source
Time‐Dependent Oxidation and Scale Evolution of a Wrought Co/Ni‐Based Superalloy
Advanced Engineering Materials, EarlyView.This study shows how a new wrought Co/Ni‐based superalloy resists oxidation at 800 ∘$^\circ$C. The oxide scale changes from rough, fast‐growing spinel to a dense, protective chromia–alumina layer. Atom probe analysis reveals tiny refractory‐rich bubbles at the interface that mark the transition to long‐term, diffusion‐controlled protection ...
Cameron Crabb +6 more
wiley +1 more source
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Advanced Engineering Materials, EarlyView.Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source
Spray Forming of al Alloys: experiment and theory
Materials Research, 2012 Close coupled gas atomization has been studied. Pitot tube gas flow measurements support a postulate of transition from an initial sonic to a supersonic and a final sonic state along the convergence region of the jets.
Georgios S. E. Antipas
doaj
Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying
Advanced Engineering Materials, EarlyView.An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara +8 more
wiley +1 more source
Preparation of Ultrafine Spherical Al-Mg Alloy and Its Energy Release Characteristics in Explosives
MetalsThe substitution of aluminum powder with highly reactive ultrafine aluminum-based metal fuels has a significant impact on the energy release of aluminum-containing energetic materials because of their excellent energy density and combustion performances.
Junhui Liu +5 more
doaj +1 more source
Recent modeling approaches to close-coupled atomization for powder production
, 2021 Additive manufacturing requires high quality, monodisperse metal powder with spherical particles of definite size. For plant operation, it is important to better understand the atomization process, i.e., to determine the influence of the operating ...
Vogl, Norbert +5 more
core