Results 101 to 110 of about 24,743 (266)

Overcoming Printing and Interfacial Challenges in Liquid Metal Direct Writing for Integrated Stretchable Electronics

Advanced Materials Technologies, EarlyView.
Liquid metal direct writing is advanced from a technological and fundamental point. Utilizing a kinematic bed, printing on large surfaces with irregularities is enabled. Furthermore, a pressure‐driven flow during printing is discovered that affects the thickness of traces.
Maximilian Krack, Lennert Purnal, Parth Vinayakrao Sewlikar, Sam Cuyvers, Gus Geurts, Rathul Nengminza Sangma, Derese Desta, Dieter Reenaers, Bart Ruttens, Iris De Graeve, Tom Hauffman, Seppe Terryn, Bram Vanderborght, Michaël Daenen, Wim Deferme, Monika Rai   +15 more
wiley   +1 more source

End‐to‐End Sensing Systems for Breast Cancer: From Wearables for Early Detection to Lab‐Based Diagnosis Chips

Advanced Materials Technologies, EarlyView.
This review explores advances in wearable and lab‐on‐chip technologies for breast cancer detection. Covering tactile, thermal, ultrasound, microwave, electrical impedance tomography, electrochemical, microelectromechanical, and optical systems, it highlights innovations in flexible electronics, nanomaterials, and machine learning.
Neshika Wijewardhane, Lyn I. Jones, Richard M. Martin, Helen Winter, Faezeh Arab Hassani   +4 more
wiley   +1 more source

Experimental and Numerical Analysis on Co-Flow Jet Airfoil

International Journal of Vehicle Structures and Systems
This project undertakes a comprehensive investigation into the aerodynamic behaviours of NACA 0018 baseline and co-flow jet (CFJ) airfoils, employing both wind tunnel tests and numerical methodologies using ANSYS Fluent. Through detailed analysis of lift coefficient (CL), stalling Angle of Attack (AoA) and drag coefficient (CD), the study aims to ...
C.M. Vigneswaran, Mohamed Hussain, R. Anand, K.Y. Chethana   +3 more
openaire   +1 more source

Large‐Scale and Cost‐Effective Fabrication of Ultra‐Thin, Biodegradable Microelectrode Arrays and Pressure Sensors Using Laser Micromachining

Advanced Materials Technologies, EarlyView.
A mask‐free and cost‐effective UV‐pico‐second laser‐based microfabrication method is proposed to fabricate large‐area biodegradable microelectrode arrays and pressure sensors. These devices demonstrate low impedance, good conformability, excellent biocompatibility, and rapid degradation, providing a new route for next‐generation transient electronics ...
Bhavani Prasad Yalagala, Asfand Tanwear, María Cerezo‐Sánchez, Hossein Parvizi, Morteza Amjadi, Hadi Heidari   +5 more
wiley   +1 more source

Characterization of Droplet Formation in Ultrasonic Spray Coating: Influence of Ink Formulation Using Phase Doppler Anemometry and Machine Learning

Advanced Materials Technologies, EarlyView.
This study explores how machine learning models, trained on small experimental datasets obtained via Phase Doppler Anemometry (PDA), can accurately predict droplet size (D32) in ultrasonic spray coating (USSC). By capturing the influence of ink complexity (solvent, polymer, nanoparticles), power, and flow rate, the model enables precise droplet control
Pieter Verding, Danny E. P. Vanpoucke, Yunus T. Aksoy, Tobias Corthouts, Maria R. Vetrano, Wim Deferme   +5 more
wiley   +1 more source

Benchmarking Coaxial and Angular Optical Emission Spectroscopy With Recommendations for Reliable Compositional In Situ Monitoring During Laser Powder Bed Fusion

Advanced Materials Technologies, EarlyView.
ABSTRACT Real‐time insight into local chemistry is critical for reliable part quality in additive manufacturing, especially laser powder bed fusion (PBF‑LB/M), where rapid thermal cycles and localized evaporation can undermine part performance. Optical emission spectroscopy (OES) offers non‑intrusive, in situ plume monitoring, but detection geometry ...
Philipp Gabriel, Bastian Jülich, Anna Rosa Ziefuss, Florian Eibl, Stephan Barcikowski   +4 more
wiley   +1 more source

Active Flow Control Technology Based on Simple Droop Devices and a Co-Flow Jet for Lift Enhancement

Aerospace
The missions of modern aircraft require multiple abilities, such as highly efficient taking-off and landing, fast arrival, and long-endurance hovering. It is difficult to achieve all technical objectives using traditional aircraft design technology.
Jin Jiao, Cheng Chen, Bo Wang, Pei Ying, Qiong Wei, Shengyang Nie   +5 more
doaj   +1 more source

Record Performance in Vertically Stacked, Solution‐Processed ZTO Schottky Diodes

Advanced Materials Technologies, EarlyView.
Schottky diodes based on solution processed sustainable zinc—tin–oxide thin films present an eco‐friendly and versatile alternative to conventional CMOS based technologies. Beyond state‐of‐the‐art performance for vertically stacked solution‐based oxide diodes was achieved, including rectification ratios exceeding nine orders of magnitude, and intrinsic
Carlos Silva, Asal Kiazadeh, Raquel Azevedo Martins, António Dias, Jorge Martins, Luís Mendes, João Vaz, Rodrigo Martins, Elvira Fortunato, Emanuel Carlos, Jonas Deuermeier   +10 more
wiley   +1 more source

Additive Manufacturing of Patient‐Specific Intracranial Aneurysm Cell Culture Models

Advanced Materials Technologies, EarlyView.
Patient‐specific intracranial aneurysm models were fabricated using chocolate moulding, 3D printed water‐soluble cores, and direct resin 3D printing. Moulding PDMS around sacrificial cores made of chocolate or 3D printed water‐soluble resin yielded accurate, expandable, and endothelializable models that outperformed resin‐based approaches.
Chloe M. de Nys, Jaimee‐Lee Wood, James I. Novak, Danilo Carluccio, Craig D. Winter, Ashley R. Murphy, Mark C. Allenby   +6 more
wiley   +1 more source

Furnace MILD combustion versus its open counterpart in hot coflow

Applications in Energy and Combustion Science
The open jet flame in hot co-flow (JHC) has been frequently utilized for fundamental investigations of Moderate or Intense Low-oxygen Dilution (MILD) combustion due to its controllable conditions and relatively easy measurement capabilities.
X. Liu, G. Wang, J. Si, M. Wu, M.F. Hanif, J. Mi   +5 more
doaj   +1 more source