Results 171 to 180 of about 1,533,791 (361)

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

Numerical and Experimental Investigation of the Effects of Thin Hard Coatings on the Strength of Spur Gears

, 2022
Sergio Baragetti
openalex   +2 more sources

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Effect of Annealing on Corrosion Resistance and Mechanical Properties of Cr-Fe-Ni-Co-Mo-Si-B Amorphous Coating

, 2023
Yuwei Liang, Mingcai Yang, Taihong Huang, Dehao Kong, Jie Wang, Zijie Yang, Biju Zheng, Pu Song   +7 more
openalex   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Elinvar Materials: Recent Progress and Challenges

Advanced Engineering Materials, EarlyView.
Elinvar materials, exhibiting temperature‐invariant elastic modulus, are critical for precision instruments and emerging technologies. This article reviews recent progress in the field, with a focus on the anomalous thermoelastic behavior observed in key material systems.
Wenjie Li, Yang Ren
wiley   +1 more source

Cover Picture: Monolithic, Crystalline MOF Coating: An Excellent Patterning and Photoresist Material (ChemNanoMat 5/2015) [PDF]

, 2015
Zhengbang Wang, Jinxuan Liu, Sylvain Grosjean, Danny Wagner, Wei Guo, Zhi‐Gang Gu, Lars Heinke, Hartmut Gliemann, Stefan Bräse, Christof Wöll   +9 more
openalex   +1 more source

Influence of Silane Sol Sealing Treatment on the Anti-Corrosion of Micro-Arc Oxidation Coating. [PDF]

Molecules
Song W, Xing Y, Xu X, Li H, Li W, Zhang P, Li Y.   +6 more
europepmc   +1 more source

Packaging of Macroscopic Material Payloads: Needs, Challenges, Concepts, and Future Directions

Advanced Engineering Materials, EarlyView.
This review introduces a unified framework that decomposes any macroscopic packaging system into the payload, packaging material, and packaging strategy and combines them into a conceptual packaging equation: packaging strategy = payload + packaging material.
Venkata S. R. Jampani, Manos Anyfantakis
wiley   +1 more source

Plasma tool as green route for incorporation of flame retardancy and ultraviolet protection of textile fabrics. [PDF]

Sci Rep
Abdel-Razik AM, Nasr HE, Attia NF.
europepmc   +1 more source