Results 51 to 60 of about 115,610 (302)

β‐Catenin/c‐Myc Axis Modulates Autophagy Response to Different Ammonia Concentrations

Advanced Biology, Volume 9, Issue 3, March 2025.
Ammonia, detoxified by the liver into urea and glutamine, impacts autophagy differently at varying levels. Low ammonia activates autophagy via c‐Myc and β‐catenin, while high levels suppress it. Using Huh7 cells and Spf‐ash mice, c‐Myc's role in cytoprotective autophagy is revealed, offering insights into hyperammonemia and potential therapeutic ...
S. Sergio, B. Spedicato, G. Corallo, A. Inguscio, M. Greco, D. Musarò, D. Vergara, A. F. Muro, G. De Sabbata, L. R. Soria, N. Brunetti Pierri, M. Maffia   +11 more
wiley   +1 more source

Microstructure‐Controlled Crack Propagation and Fracture Resistance in MoSiBTiC Alloy Revealed by Multiscale Extended Finite Element Method Modeling

Advanced Engineering Materials, EarlyView.
A two‐dimensional multiscale finite element analysis framework was established for the first‐generation MoSiBTiC alloy, and the mechanical and fracture‐related parameters of the constituent phases were calibrated through experiments and simulations. The framework provides a basis for analyzing crack propagation behavior in its complex microstructure ...
Junfeng Du, Takahiro Kaneko, Xinyu Yan, Takahito Ohmura, Kyosuke Yoshimi   +4 more
wiley   +1 more source

The Effect of Total Solids on the Discharge Coefficient of Spillway, Broad crested weir and Crump weir

Journal of Engineering and Sustainable Development, 2013
In this experimental work the efforts was devote to study the effect of different amounts of total solids (TS) on the flow rate pattern and the coefficient of discharge in open channels and water treatment plant for ogee spillway, broad crested weir and
Safaa Nasser Hassan
doaj  

Experimental investigation of the discharge coefficient of labyrinth weirs with asymmetric cycles

, 2022
This  study investigated the discharge coefficient in asymmetric rectangular labyrinth weirs. A dimensional analysis was carried out which showed that the discharge coefficient is a function of dimensionless parameters, such as the ratio of ...
Mehdi Momeni, Hossein Elahifar, Najme Yazdanpanah, Omid Tayari   +3 more
core   +1 more source

Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys

Advanced Engineering Materials, EarlyView.
Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak, Olha Zvirko, Rostyslav Leshchak, Hryhoriy Nykyforchyn   +3 more
wiley   +1 more source

Influence of the wall roughness on discharge coefficient of orifice

, 2015
This thesis deals with the influence of the wall roughness on discharge coefficient of sharp-edged circular bottom orifice. It supposed to verify, summarize and extend knowledge of orifice discharge.
Jinek, Josef
core   +2 more sources

Temporal variation in discharge coefficients of non-point source pollution and its determinants in river-network areas in a plain

Guan'gai paishui xuebao
【Objective】 Discharge coefficient is a coefficient describing the discharge of non-point source pollution to water bodies. It is affected by many biotic and abiotic factors.
DUANMU Jiayao, CHEN Cheng, CHEN Xiaohua, SHEN Genxiang, ZHANG Min, GUO Chunxia, WANG Zhenqi, BAI Yujie, LING Zhixiong, CAO Guomin   +9 more
doaj   +1 more source

The effect of crest shape on discharge coefficient at linear weirs

Građevinar, 2023
A detailed experimental laboratory analysis of the effect of crest shape on the discharge coefficient of sharp-crested weirs is presented in the paper. The experiments were conducted for four different crest shapes. The experiments and analyses show that
Yusuf Dogan, Nihat Kaya
doaj   +1 more source

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

Advanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara, Vincent Rat, Quentin Dubreuil, Patrice Valorge, Simon Goutier, Alain Denoirjean, Olivier Messe, Céline Ruelle, Jean‐Philippe Poli   +8 more
wiley   +1 more source