Results 161 to 170 of about 410,815 (307)
Arthritis Care &Research, Accepted Article.Objective The objective of this article is to identify perceptions of SLE patients regarding artificial intelligence (AI)‐based online symptom assessment tools, and the potential of these tools to address diagnostic barriers. Methods Adults from our SLE research cohort were invited to participate in 60‐90 minute virtual focus groups concerning their ...
Olivia A. Stein +7 more
wiley +1 more source
RF coil design for accurate parallel imaging on <sup>13</sup> C MRSI using <sup>23</sup> Na sensitivity profiles. [PDF]
Magn Reson Med, 2022 Sanchez-Heredia JD +10 more
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
The PIT MkV pulsed inductive thruster [PDF]
The pulsed inductive thruster (PIT) is an electrodeless, magnetic rocket engine that can operate with any gaseous propellant. A puff of gas injected against the face of a flat (spiral) coil is ionized and ejected by the magnetic field of a fast-rising ...
Dailey, C. Lee, Lovberg, Ralph H.
core +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Optimal Design of Control Loop of Special Breaker of 10 kV Capacitor Bank
Gong-kuang zidonghua, 2012 In view of problem that closing coil in control loop of breaker often happens burnout when breaker of 10 kV capacitor bank makes breaking-closing control operation, the paper proposed an optimal design scheme of double control loops of closing coil of ...
CUI Yong +3 more
doaj
Advanced Engineering Materials, EarlyView.This study demonstrates how optimizing laser power, scanning speed, and hatching distance in laser powder bed fusion can boost the productivity of Inconel 718 manufacturing by up to 29% while maintaining mechanical integrity. The work delivers a validated process window and cost–time analysis, offering industry‐ready guidelines for efficient additive ...
Amir Behjat +7 more
wiley +1 more source
Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May +9 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee +7 more
wiley +1 more source
An Experimental High‐Throughput Approach for the Screening of Hard Magnet Materials
Advanced Engineering Materials, EarlyView.An entire workflow for the high‐throughput characterization and analysis of compositionally graded magnetic films is presented. Characterization protocols, data management tools and data analysis approaches are illustrated with test case Sm(Fe, V)12 based films.
William Rigaut +16 more
wiley +1 more source