Results 61 to 70 of about 369,149 (300)
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Cold - formed steel structures in fire conditions [PDF]
, 2007 L’aparició en els darrers anys arreu del món de normatives i codis per a fer front a les situacions d’incendi han provocat que cada vegada més es tingui en compte aquesta situació alhora de projectar les estructures, ja que un bon disseny pot ajudar a ...
Pastó Carmona, Elsa
core
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Bearing Capacity of Light-Steel Compound Section and Steel Columns under Axial Compression
Advances in Civil Engineering, 2022 In the international trend of vigorously developing low-carbon economy and green buildings, environmental protection and conservation have received increased attention in the construction field.
Jianwen Li +3 more
doaj +1 more source
Thermomechanical analysis of cold formed steel sections [PDF]
, 2016 This work presents an experimental study about cold formed steel elements submitted to compression loads. The sections analyzed are C and Z sections made of steel sheet with 1.5 and 2 [mm] thick and three different cross section heights.
Barreira, Luísa +4 more
core
Advanced Engineering Materials, EarlyView.This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert +7 more
wiley +1 more source
Evaluation indexes quality, cost and time at Lightweight steel structures (case study:LSF structures in yazd city) [PDF]
مهندسی و مدیریت ساخت, 2017 Building and Hausas are the nowadays necessity of people's life, the most permanent part of economy of a family or a country. But type and the approach of construction a building. Than it can be a kind stable investment or in the other hand the structure
Seyed Shahabaldin Mirjafari
doaj
Flexural performance of built-up cold-formed steel beam filled with compacted soil [PDF]
, 2016 Cold-formed steel is the well-liked structural materials in the construction industry and used as an alternative construction material upon the traditional material such as reinforced concrete, hot-rolled steel or timber. The purpose of compacted soil is
Kamal, M. M. +3 more
core
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Fastener Demands for Sheathing-Braced Cold-Formed Steel Stud Gravity Walls
Latin American Journal of Solids and StructuresWe explore, in this paper, the demands and behavior on fasteners supplying sheathing-based bracing of gravity loaded cold-formed studs and wall assemblies.
Luiz Carlos M. Vieira Junior +1 more
doaj +1 more source