Results 151 to 160 of about 3,581,165 (352)

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

Determination of aluminium properties under bulk cold forming processes

, 2008
Consulta en la Biblioteca ETSI Industriales (7816)
openaire   +2 more sources

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Numerical and experimental analysis of edge wave defect control during TA2 circular tube cold roll forming

Engineering Reports
The increasing application of TA2 titanium profiles in marine and petrochemical industries has spurred in a growing demand for diverse forms, including U‐shaped, rectangular, and tubular thin‐walled profiles.
Mingze Yue, Jing Zhang, Bing Xiao, Gang Chen, Qiang Fang, Xinxin Tang, Biyou Peng   +6 more
doaj   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source

Dynamic Testing of Cold Gas Sprayed Bipolar Plates–Porous Transport Layer Coating System in Proton Exchange Membrane Water Electrolysis

Advanced Engineering Materials, EarlyView.
Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin, Marvin Erck, Kevin Jasutyn, Katja Radermacher, Andreas Bund, Mario Kurniawan   +5 more
wiley   +1 more source

Corrosion and Process Analysis of a Preoxidized MgO Recyclate‐Based Cermet Anode in Laboratory‐Scale Na‐Cryolite Molten Salt Electrolysis of Aluminum at 1000°C

Advanced Engineering Materials, EarlyView.
EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk, Farhan Hossain, Felipe A. Garcia Paz, Serhii Yaroshevskyi, Felix Drechsler, Daniel Vogt, Christos G. Aneziris, Alexandros Charitos   +7 more
wiley   +1 more source

Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing

Advanced Engineering Materials, EarlyView.
The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai, Zeki Ayrildi, Buse Şen, Maik Rajkowski, Mathias Redondo Garcia, Markus Stricker, Guillaume Laplanche   +6 more
wiley   +1 more source

Bias‐Free Highly Efficient and Stable Dye‐Sensitized Photoelectrochemical Cells via Cascade Charge Transfer

Advanced Functional Materials, EarlyView.
A buried‐junction DSPEC design is introduced that leverages cascade charge transfer to enhance efficiency, stability, and versatility. This approach facilitates effective charge transfer and minimizes recombination losses, leading to significant improvements.
Jun‐Hyeok Park, Kyounglim Kim, Jinyoung Lee, Sarang Kim, Gwangsu Yoon, So Yeon Yoon, Jeong Kyeong Lee, Ji‐Wook Jang, Tae‐Hyuk Kwon   +8 more
wiley   +1 more source

The Structural Examination of Fe/(Cu/Nb)/MgB2 Multifilament Wires During Cold Forming Process

Journal of Advanced Applied Sciences
In this study, we have successfully produced a Fe-sheathed 6+1 multifilament wire using Cu/Nb/MgB2 monocore wires. The mono filament wire was prepared using Mg+2B powder mixture by powder-in-tube method without any intermediate heat treatment. The powder mixture of the amorphous nano boron (PVZ Nano Boron, purity of 98.5%, particle sizes < 250 nm ...
Doğan Avcı, Hakan Yetiş, Fırat Karaboğa, İbrahim Belenli   +3 more
openaire   +1 more source