Results 71 to 80 of about 98,877 (294)
Processing and microstructure of Nb-1 percent Zr-0.1 percent C alloy sheet [PDF]
A systematic study was carried out to evaluate the effects of processing on the microstructure of Nb-1 wt. pct. Zr-0.1 wt. pct. C alloy sheet. The samples were fabricated by cold rolling different sheet bars that were single-, double- or triple-extruded ...
Titran, Robert H., Uz, Mehmet
core +1 more source
Advanced Science, EarlyView.This review provides an integrated framework for achieving superior electrochemical performance in sulfide‐based all‐solid‐state batteries. It first delineates mechano‐electrochemical failure modes of cathode active materials and solid electrolytes, then outlines engineering principles for particle morphology, electronic and ionic conduction, and ...
Gawon Song +4 more
wiley +1 more source
Teshugang, 2010 The 0.5-2.5 mm cold rolled sheet of test magnetic pure iron is rolled by 350 mm four high reversing finishing mill from 3.5-4.5 mm hot continuous rolled plate of magnetic pure iron (% ： 0.005C, 0.50 Al).
谢振亚
doaj
Advanced Energy and Sustainability Research, EarlyView.Hydrogen‐powered aviation offers a transformative pathway to zero‐emission flight by eliminating in‐flight CO2 emissions. Key considerations include propulsion systems (fuel cells and hydrogen combustion), cryogenic storage and insulation challenges, infrastructure and cost barriers, and supply‐chain constraints.
Mubasshira +4 more
wiley +1 more source
Teshugang, 2017 The rolling flow sheet for tested oriented silicon steel cold-rolled sheet (/% : 0.050C, 3.20Si, 0.15Mn, 0.003S, 0.023Als, 0.0090N) is 220 mm cast slab-hot rolled to 1.8 mm plate-normalized at 1120℃.
谢力 +5 more
doaj
Micro Crack of Aluminum Sheet During Cold Rolling
World Journal of Mechanics, 2011 The micro crack of aluminum sheet during cold rolling lubricated with emulsions is investigated. Experi-ments show that micro cracks occur after cold rolling process and this is attributed to various parameters, for instance, the thin oxide film formed at the sheet surface. The micro crack spacing thus becomes an important parameter which deserves more
Chaohui Zhang, Sisi Liu, Chenhui Zhang
openaire +2 more sources
Numerical Treatments of Slipping/No-Slip Zones in Cold Rolling of Thin Sheets with Heavy Roll Deformation [PDF]
, 2015 International audienceIn the thin sheet cold rolling manufacturing process, a major issue is roll elastic deformation and its impact on roll load, torque and contact stresses.
Montmitonnet, Pierre +2 more
core +3 more sources
Copper Contact for Perovskite Solar Cells: Properties, Interfaces, and Scalable Integration
Advanced Energy and Sustainability Research, EarlyView.Copper electrodes, as low‐cost, scalable contacts for perovskite solar cells, offer several advantages over precious metals such as Au and Ag, including performance, cost, deposition methods, and interfacial engineering. Copper (Cu) electrodes are increasingly considered practical, sustainable alternatives to noble‐metal contacts in perovskite solar ...
Shuwei Cao +4 more
wiley +1 more source
Teshugang, 2008 The recrystallized annealed structure and HB hardness of DDQ(Deep Drawable Quality)cold-rolled deep drawing sheet of0.003C-0.05Al-0.06Cu steel produced by TSCR(Thin Slab Casting and Rolling)process have been test- ed and researched.
杨奕 +5 more
doaj
Smart Bioinspired Material‐Based Actuators: Current Challenges and Prospects
Advanced Intelligent Systems, Volume 7, Issue 3, March 2025.This work gathers, in a review style, an extensive and comprehensive literature overview on the development of autonomous actuators based on synthetic materials, bringing together valuable knowledge from several studies. Furthermore, the article identifies the fundamental principles of actuation mechanisms and defines key parameters to address the size
Alejandro Palacios +4 more
wiley +1 more source